NATO EPVAT testing

NATO EPVAT testing
Left to right: 7.62 mm NATO, 5.56 mm NATO and 9 mm NATO ammunition.

NATO EPVAT testing is one of the three recognized classes of procedures used in the world to control the safety and quality of firearms ammunition.

Beside this, there are also the Commission Internationale Permanente pour l'Epreuve des Armes à Feu Portatives (CIP) class of procedures and the Sporting Arms and Ammunition Manufacturers' Institute (SAAMI) class of procedures.

EPVAT Testing is described in unclassified documents by NATO, more precisely by the AC/225 Army Armaments Group (NAAG).[1]

EPVAT is an abbreviation for "Electronic Pressure Velocity and Action Time". This is a comprehensive procedure for testing ammunition using state-of-the-art instruments and computers. The procedure itself is described in NATO document AC/225 (Com. III/SC.1)D/200.

Unlike the C.I.P. procedures aiming only at the user's safety, the NATO procedures for ammunition testing also includes comprehensive functional quality testing in relation with the intended use. That is, not only the soldier's safety is looked at, but also his capacity to incapacitate the enemy. As a result, for every ammunition order by NATO, a complete acceptance approval on both safety and functionality is performed by both NATO and the relevant ammunition manufacturers in a contradictory fashion.

For this, a highly accurate and indisputable protocol has been defined by NATO experts using a system of reference cartridges.[1][2][3]

The civilian organisations C.I.P. and SAAMI use less comprehensive test procedures than NATO, but NATO test centres have the advantage that only a few chamberings are in military use. The C.I.P. and SAAMI proof houses must be capable of testing hundreds of different chamberings requiring lots of different test barrels, etc..

Contents

NATO Reference cartridges system

In this system, the ammunition manufacturers, in close cooperation with NATO, have set aside a batch (also termed "lot") of ammunition they consider to be of very good quality and representative of ammunition that should be delivered to the armies in the next following years. This batch is maintained at approved NATO test centres and distributed to the manufacturers involved. When a new batch (lot) is delivered, a set of 20 reference cartridges are fired to see how they behave with the local equipment and with the current atmospheric conditions. Results are then compared to the reference values as maintained by the NATO and correctors (delta values) are computed. Then, the current batch (lot) of ammunition is fired and the correctors are applied on the measured value giving a result "comparable" to the reference itself.

This test is performed under normal conditions but also by simulating extreme polar or desert conditions using special cooling equipment and ovens to cool or heat the tested ammunition to the appropriate temperatures.[4][5]

Proofing

The minimum proof and performance requirements for small arms ammunition of NATO calibres are covered in STANAGs as follows:

  • 5.56 mm. STANAG 4172 and NATO Manual of Proof and Inspection AC/225 (LG/3-SG/1) D/8.
  • 7.62 mm. STANAG 2310 and NATO Manual of Proof and Inspection AC/225 (LG/3-SG/1) D/9.
  • 9 mm. STANAG 4090 and NATO Manual of Proof and Inspection AC/225 (P111-SP1) D/170(REV).
  • 12.7 mm. STANAG 4383 and NATO Manual of Proof and Inspection AC/225 (LG/3-SG/1) D/11.

Each weapon and component considered vulnerable to the effects of a rapid change in pressure, for example barrels, breech blocks and bolts, will be tested by firing one dry round at a corrected minimum of 25% over pressure and one oiled round at a corrected minimum of 25% over pressure. 25% over pressure means 25% in excess of the Service Pressure (Pmax). The Service Pressure is defined as the mean pressure generated by the Service Cartridge at a temperature of 21°C. Such a high pressure proof is conducted with both the weapon and ammunition conditioned to an ambient temperature of 21°C.

Each weapon will be individually tested, from an ammunition lot that produces a minimum corrected mean chamber pressure in accordance with the table below:[1]

Corrected Proof Pressure Requirement (Service Pressure (Pmax) + 25%)
Calibre Specific Weapon Detail Service Pressure Pmax
MPa / (psi)
Proof Round Pressure Requirement
MPa / (psi)
Detailed Requirement for Proof Ammunition
5.56 mm (5.56×45mm NATO) Designed to chamber NATO ammunition 430.0 / (62,366) 537.5 / (77,958) Pressure recorded in NATO design EPVAT Barrel with Kistler 6215 Transducer[6] or by equipment to Commission Internationale Permanente pour l’épreuve des Armes á Feu Portatives (C.I.P.) requirements
7.62 mm (7.62×51mm NATO) Designed to chamber NATO ammunition 415.0 / (60,190) 519.0 / (75,275) Pressure recorded in NATO design EPVAT Barrel with Kistler 6215 Transducer or by equipment to C.I.P. requirements
9 mm (9×19mm NATO) Designed to chamber NATO ammunition 252.0 / (36,550) 315.0 / (45,687) Pressure recorded in C.I.P. design barrel at mid case position
12.7 mm (12.7×99mm NATO) Designed to chamber NATO ammunition 417.0 / (60,481) 521.3 / (75,608) Pressure recorded in NATO design EPVAT Barrel with Kistler 6215 Transducer or by equipment to C.I.P. requirements
All other small arms ammunition for use in "non-NATO Chamber" weapons As defined by the current C.I.P. legislation. As defined by the current C.I.P. legislation.

The above proof round pressure requirements for the 9 mm and 12.7 mm rounds established by the British Ministry of Defence are higher than the current (2008) C.I.P. proof round pressure requirement legislation for the civilian equivalent 9mm Parabellum (C.I.P. Pmax rating 235 MPA / (34,083 psi) and .50 Browning (C.I.P. Pmax rating 370 MPA / (53,663 psi) rounds.[7] The 9x19mm NATO round can be regarded as overpressure ammunition

Testing equipment providers

The following companies provide equipment to the NATO armies to perform this type of testing: (inexhaustive list)

See also

References

Notes
Bibliography

External links


Wikimedia Foundation. 2010.

Игры ⚽ Нужен реферат?

Look at other dictionaries:

  • 5.56×45mm NATO — 5.56x45mm NATO with measurement Type Rifle Place of origin …   Wikipedia

  • 7.62x51mm NATO — Infobox Firearm Cartridge name=7.62x51mm NATO caption=7.62x51mm NATO rounds compared to AA (LR6) battery. origin=flagcountry|United States type=Rifle designer= design date= service=1954 present used by=United States, NATO, others. wars=… …   Wikipedia

  • 5.56x45mm NATO — Infobox Firearm Cartridge name=5.56x45mm NATO caption=5.56x45mm NATO (left) next to .30 30 (center) and 7.62x51mm NATO (right) origin=flagcountry|United States type=Rifle used by=NATO wars= designer=Remington Arms is SI specs=yes parent=.223… …   Wikipedia

  • Commission Internationale Permanente pour l'Epreuve des Armes à Feu Portatives — C.I.P. C.I.P. logo Formation 1914 Type standards organization Headquarters …   Wikipedia

  • 9x19mm Parabellum — Infobox Firearm Cartridge name=9x19mm Parabellum caption=Ball and hollow point 9 mm Parabellum rounds origin=flag|German Empire type=Centerfire designer=Georg Luger design date=1901 manufacturer= production date=1902 to present number= variants=… …   Wikipedia

  • Proof test — A proof test is a test wherein a deliberately overpressured round is fired from a firearm in order to verify that the firearm is not defective and will not explode on firing. The firearm is inspected after the test, and if it is found to be in… …   Wikipedia

  • .50 BMG — Infobox Firearm Cartridge name=.50 BMG caption=From left: .50 BMG, 300 Win Mag, .308 Winchester, 7.62x39mm, 5.56x45mm NATO, .22LR origin=flagcountry|United States type= Rifle service=1914 present used by=NATO and many others wars=WWI, WWII,… …   Wikipedia

  • Sporting Arms and Ammunition Manufacturers' Institute — The American Sporting Arms and Ammunition Manufacturers Institute (commonly abbreviated as SAAMI and pronounced Sammy ) is an association of American firearms and ammunition manufacturers. SAAMI publishes various industry standards related to the …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”