Eb/N0

"E"_b/"N"₀ (the energy per bit to noise power spectral density ratio) is an important parameter in digital communication or data transmission. It is a normalized signal-to-noise ratio (SNR) measure, also known as the "SNR per bit". It is especially useful when comparing the bit error rate (BER) performance of different digital modulation schemes without taking bandwidth into account.

"E"_b/"N"₀ is equal to the SNR divided by the "gross" link spectral efficiency in (bit/s)/Hz, where the bits in this context are transmitted data bits, inclusive of error correction information and other protocol overhead. It should be noted that when forward error correction is being discussed, "E"_b/"N"₀ is routinely used to refer to the energy per information bit (i.e. the energy per bit net of FEC overhead bits). In this context, E_s/N₀ is generally used to relate actual transmitted power to noise.

The noise spectral density "N"₀, usually expressed in units of watts per hertz, that is, joules-per-second per cycles-per-second, can also be seen as having dimensions of energy, or units of joules, or joules per cycle. "E"_b/"N"₀ is therefore a non-dimensional ratio.

"E"_b/"N"₀ is commonly used with modulation and coding designed for power-limited, rather than bandwidth-limited communications.Examples of power-limited communications include deep-space and spread spectrum, and is optimized by using large bandwidths relative to the bit rate.

Relation to carrier-to-noise ratio

E_b/N₀ is closely related to the carrier-to-noise ratio (CNR or C/N), i.e. the signal-to-noise ratio (SNR) of the received signal, after the receiver filter but before detection:

:$C/N=E\_b/N\_0cdotfrac\{f\_b\}\{B\}$

where:"f"_b is the channel data rate (gross bitrate), and:"B" is the channel bandwidth

The equivalent expression in logarithmic form (dB):

:$CNR\_\{dB\}\; =\; 10log\_\{10\}(E\_b/N\_0)\; +\; 10log\_\{10\}(frac\{f\_b\}\{B\})$,

Relation to E_s/N₀

"E"_b/"N"₀ can be seen as a normalized measure of the energy per symbol per noise power spectral density ("E"_s/"N"₀), where "E"_s is the Energy per symbol in Joules. This measure is also commonly used in the analysis of digital modulation schemes. The two quotients are related to each other according to the following:

:$frac\{E\_s\}\{N\_0\}\; =frac\{E\_b\}\{N\_0\}log\_2\; M$,

where

:"M" is the number of alternative modulation symbols.

"E"_s/"N"₀ can further be expressed as:

:$frac\{E\_s\}\{N\_0\}\; =\; frac\{C\}\{N\}frac\{B\}\{f\_s\}$,

where:"C/N" is the carrier-to-noise ratio or signal-to-noise ratio.:"B" is the channel bandwidth in Hertz.:"f"_s is the symbol rate in baud or symbols/second.

For a PSK, ASK or QAM modulation with pulse shaping such as raised cosine shaping, the "B"/"f"_s ratio is usually slightly larger than 1, depending of the pulse shaping filter.

hannon limit

The Shannon–Hartley theorem says that the limit of reliable data rate of a channel depends on bandwidth and signal-to-noise ratio according to:

:

where:"R" is an information rate in bits per second;:"B" is the bandwidth of the channel in hertz; : "S" is the total signal power (equivalent to the carrier power "C"); and: "N" is the total noise power in the bandwidth.

This equation can be used to establish a bound on E_b/N₀ for any system that achieves reliable communication, by considering a bit rate equal to "R" and therefore an average energy per bit of E_b = "S/R", with noise spectral density of N₀ = "N/B". For this calculation, it is conventional to define a normalized rate R_l = "R/"(2"B"), a bandwidth utilization parameter of bits per second per half hertz, or bits per dimension (a signal of bandwidth "B" can be encoded with 2"B" dimensions, according to the Nyquist–Shannon sampling theorem). Making appropriate substitutions, the Shannon limit is:

:

Which can be solved to get the Shannon-limit bound on E_b/N₀:

:$frac\{E\_b\}\{N\_0\}\; >\; frac\{2^\{2R\_l\}-1\}\{2R\_l\}$

When the data rate is small compared to the bandwidth, so that R_l is near zero, the bound, sometimes called the "ultimate Shannon limit", [cite book | title = Algorithms for Communications Systems and Their Applications | author = Nevio Benvenuto and Giovanni Cherubini | ISBN 0470843896 | year = 2002 | page = 508 | publisher = John Wiley & Sons] is:

:$frac\{E\_b\}\{N\_0\}\; >\; ln(2)$

which corresponds to –1.59 dB.

Cutoff rate

For any given system of coding and decoding, there exists what is known as a "cutoff rate" R_0, typically corresponding to an E_b/N₀ about 2 dB above the Shannon capacity limit. The cutoff rate used to be thought of as the limit on practical error correction codes without an unbounded increase in processing complexity,but has been rendered largely obsolete by the more recent discovery of turbo codes.

References

External links

* [http://www.sss-mag.com/ebn0.html Eb/N0 Explained.] An introductory article on E_b/N₀