Bend Arch-Fort Worth Basin

Bend Arch-Fort Worth Basin

Infobox Oil field
name = Bend Arch-Fort Worth Basin Province
region = North-Central Texas
country = United States
coordinates =
locblock =
offonshore = Onshore
operators = Devon Energy, Chesapeake Energy, EOG Resources, XTO Energy, EnCana, Range, ConocoPhillips, Quicksilver, Denbury
partners =


caption =
discovery = 1900s
startofproduction = 1917
peakofproduction = 1960s
expectedabandonment =
currentproductionoil =
currentproductiongas = convert|200|Gcuft (2002)
estimatedstoiip =
estimatedgiip =
producingformations = Barnett Shale, Ordovician, Permian
The Bend Arch-Fort Worth Basin Province is a major petroleum producing geological system which is primarily located in north central Texas and southwestern Oklahoma. It is officially designated by the United States Geological Survey (USGS) as Province 045 and classified as the Barnett-Paleozoic Total Petroleum System (TPS).

Introduction

Oil and gas in Province 045 are produced from Carbonate rock- and clastic-rock reservoirs ranging in age from the Ordovician to the Permian. The 1995 USGS Assessment of undiscovered, technically recoverable oil and gas identified six conventional plays in Province 045, which are listed below in Table 1: [Ball, 1996] One continuous unconventional play, hypothetical “Mississippian Barnett Shale” (4503), was also considered. The cumulative mean of undiscovered resource for conventional plays was: convert|381|Moilbbl of oil, convert|103.6|Moilbbl of natural gas liquids, convert|479|Gcuft associated gas, and convert|1029|Gcuft non-associated gas.

Table 1

Notes:
1.Assessment unit number also indicates time span of stratigraphic units.

The USGS assessment of undiscovered conventional oil and gas and undiscovered continuous (unconventional) gas within Province 045 resulted in estimated means of convert|26.7|Tcuft (Tcf) of undiscovered natural gas, convert|98.5|Moilbbl of undiscovered oil, and a mean of convert|1.1|Goilbbl of undiscovered natural gas liquids. Nearly all of the undiscovered gas resource (98%, nowrap|2.62 × 1013 cu ft or nowrap|7.4 × 1011 m3) is considered to be in continuous accumulations of nonassociated gas trapped in strata of two of the three Mississippian-age Barnett Shale Assessment Units (AUs) - the Greater Newark East Frac-Barrier Continuous Barnett Shale Gas AU and the Extended Continuous Barnett Shale Gas AU nowrap|(2.62 × 1013 cu ft combined). The remaining convert|467|Gcuft of undiscovered gas resource in the Province is in conventional nonassociated gas accumulations nowrap|(3.586 × 1011 cu ft or nowrap|1.015 × 1010 m3) and associated/dissolved gas in conventional oil accumulations (nowrap|1.084 × 1011 cu ft or nowrap|3.07 × 109 m3). The Barnett-Paleozoic TPS is estimated to contain a mean of convert|409.2|Gcuft of conventional gas, or about 88% of all undiscovered conventional gas, and about convert|64.6|Moilbbl of conventional oil, or about 65% of all undiscovered oil in Province 045.

Continuous-type accumulations include fractured shale and fractured chalk oil and gas, basin-centered gas, coal bed gas, and tight reservoir gas. They typically cover large areas, have source rocks in close association with these unconventional reservoir rocks, and are mostly gas (and in some cases oil) charged throughout their extent. [Schmoker, 1996] Continuous accumulations commonly have transition zones that grade into more conventional accumulations. [Pollastro, 2001]

Boundary

With the exception of the southwestern corner of Oklahoma, Province 045 lies entirely within north central Texas covering an area of convert|54000|sqmi|km2. The southern and eastern boundaries are defined by county lines that generally follow the Ouachita structural front, although a substantial portion of this structural feature is included near Dallas. The north boundary follows the Texas-Oklahoma State line in the east, where the province includes parts of the Sherman Basin and Muenster Arch. In the west, the north boundary follows the north-east county lines of Oklahoma's three southwestern counties (Harmon, Jackson and Tillman Counties), which include the south flank of the Wichita Mountains and the Hollis Basin. The western boundary trends north-south along county lines defining the junction with the Permian Basin where part of the eastern shelf of the Permian Basin lies in Province 045.

tructural elements

Major structural features include the Muenster and Red River Arches to the north, and the Bend and Lompasas Arches along the central part of Province 045. Along the east portion is an area that includes the Eastern and Chappel Shelves and Concho Arch, collectively known as the "Concho Platform". The Mineral Wells fault runs northeast-southwest through Palo Pinto, Parker, Wise, Denton Counties and joins with the Newark East fault system. The fault system bisects the Newark East Field (NE-F) creating a zone of poor production in Barnett Shale gas reservoirs. Several faults that cut basement and lower Paleozoic rocks in the southern part of the province are identified at the Ordovican Ellenburger Group stratigraphic level. These faults and associated structures formed during development of the Llano Uplift and Fort Worth Basin with faulting ending by the early Missourian. [Flippen, 1982]

Tectonic history

Fort Worth Basin

Evolution of the Fort Worth Basin and Bend Arch structures are critical to understanding burial histories and hydrocarbon generation. The asymmetrical, wedge-shaped Fort Worth Basin is a peripheral Paleozoic foreland basin with about convert|12000|ft|m of strata preserved in its deepest northeast portion and adjacent to the Muenster Arch and Ouachita structural belt. The basin resembles other basins of the Ouachita structural belt, such as the Black Warrior, Arkoma, Val Verde, and Marfa Basins that formed in front of the advancing Ouachita structural belt as it was thrust onto the margin of North America. Thrusting occurred during a late Paleozoic episode of plate convergence. [Flippen, 1982]

Bend Arch

The Bend Arch extends north from the Llano Uplift; it is a broad subsurface, north-plunging, positive structure. The arch formed as a hingeline by down-warping of its eastern flank due to subsidence of the Fort Worth Basin during early stages of development of the Ouachita structural belt in the Late Mississippian, and west tilting in the late Paleozoic, which formed the Midland Basin. There is disagreement on the structural history of the Bend Arch. Flippen (1982) suggested it acted as a fulcrum and is a flexure and structural high and that only minor uplift occurred in the area to form the unconformable surface above the Comyn Limestone. In contrast, Cloud and Barnes (1942) suggested periodic upwarp of the Bend flexure from mid-Ordovician through Early Pennsylvanian time resulted in several erosional unconformities. The Red River Arch and the Muenster Arch also became dominant structural features during the Late Mississippian and Early Pennsylvanian. [Flippen, 1982]

General stratigraphy

Hydrocarbon production from Ordovician, Mississippian, and Early Pennsylvanian rocks is mostly from carbonate rock reservoirs, whereas production in the Mid-Pennsylvanian through Low-Permian is mostly from clastic rock reservoirs. The sedimentary section in the Fort Worth Basin is underlain by Precambrian granite and diorite. Cambrian rocks include granite conglomerate, sandstones, and shale that are overlain by marine carbonate rocks and shale. No production has been reported from Cambrian rocks. The Silurian, Devonian, Permian, Jurassic, and Triassic are absent in the Fort Worth Basin. [Flippen, 1982]

From Cambrian to Mississippian time, the Fort Worth Basin area was part of a stable cratonic shelf with deposition dominated by carbonates. Ellenburger Group carbonate rocks represent a broad epeiric carbonate platform covering most of Texas during the Early Ordovician. A pronounced drop in sea level at the end of Ellenburger deposition resulted in prolonged platform exposure and development of extensive karst features in the upper part of the carbonate rock sequence. Moreover, a later major erosional event removed any Silurian and Devonian rocks (post Viola Limestone unconformity) that may have been present. [Henry, 1982] Barnett Shale was deposited over the resulting unconformity. Provenance of the terrigenous material that constitutes the Barnett Shale was from Ouchita thrust sheets and the reactivation of older structures such as the Muenster Arch. Clastic rocks of similar provenance dominate the Pennsylvanian part of the stratigraphic section in the Bend Arch-Forth Worth Basin. With progressive subsidence of the basin during the Pennsylvanian, the western basin hinge line and carbonate shelf, represented by carbonate rocks of the Comyn, Marble Falls, Big Saline, and Caddo Formations, continued migrating west. Deposition of thick basinal clastic rocks of the Atoka, Strawn, and Canyon Formations occurred at this time. [Walper, 1982] These Mid- and Late Pennsylvanian rocks consist mostly of sandstones and conglomerates with fewer and thinner limestone beds.

Petroleum production history

Hydrocarbon shows were first encountered in Province 045 during the mid-nineteenth century while drilling water wells. Sporadic exploration began following the Civil War, and the first commercial oil discoveries occurred in the early 1900s. [Ball, 1996] In 1917, discovery of Ranger field stimulated one of the largest exploration and development “booms” in Texas. Ranger field produces from the Atoka-Bend formation, a sandstone-conglomerate reservoir that directly overlies the Barnett formation. Operators drilled more than 1,000 wildcats in and around the Fort Worth basin attempting to duplicate the success of Ranger. These wildcat efforts resulted in the discovery of more fields and production from numerous other reservoirs including Strawn fluvial/deltaic sandstone, Atoka-Bend fluvial/deltaic sandstone and conglomerate, Marble Falls carbonate bank limestone, Barnett siliceous shale, and Ellenburger dolomitic limestone. By 1960, the Province reached a mature stage of exploration and development, as demonstrated by the high density and distribution of well penetrations and production wells. Oil and lesser amounts of gas are found throughout the Paleozoic section, but most hydrocarbons consist of oil in Pennsylvanian reservoirs.

Province 045 is among the more active drilling areas during the resurgence of U.S. drilling, which began after the OPEC oil embargo. It has consistently appeared on the list of the 10 most active provinces in terms of wells completed and footage drilled. 9,177 oil wells and 4,520 gas wells were drilled and completed in this area from 1974 to 1980. The reason for the high activity was the combination of relatively shallow depths (2,000–6,000 ft or 600–1800 m) combined the high producing rates.

Cumulative production in Province 045 from conventional reservoirs prior to the 1995 USGS Assessment was convert|2|Goilbbl of oil, convert|7.8|Tcuft of gas, and convert|500|Moilbbl of natural gas liquids. Cumulative gas production through 2001 from the continuous Barnett fractured shale play in Wise and Denton counties was about convert|440|Gcuft. Cumulative gas production from the Barnett Shale for the first half of 2002 was convert|94|Gcuft; [Texas Railroad Commission, 2202] annual production for 2002 was estimated at convert|200|Gcuft. Currently, over convert|2.5|Tcuft of proven gas reserves are assessed for NE-F. These production and proven reserve figures for the Barnett play, combined with estimates of underdeveloped Barnett resources indicate that technically recoverable continuous gas, and to a lesser extent oil, from fractured Barnett Shale will provide the greatest additions to near-future reserves in Province 045.

Petroleum data: selected fields

ource rock

The primary source rock of the Bend Arch-Fort Worth Basin is Mississippian-Pennsylvanian Barnett Shale. Barnett Shale commonly exhibits high gamma-ray log response at the base of the unit. Other potential source rocks of secondary importance are Early Pennsylvanian and include (1) dark fine-grained carbonate rock and shale units within the Marble Falls Limestone, (2) black shale facies of the Smithwick Shale, and (3) several thin Pennsylvanian coal beds in Wise, Jack, Young, Parker, Palo Pinto, and McCulloch Counties. [Mapel et al., 1979] Barnett Shale was deposited over much of North-Central Texas; however, because of post-depositional erosion, the present distribution of Barnett is limited to Province 045. [Maple et al., 1979] The Barnett Shale is over convert|1000|ft|m thick along the southwest flank of the Muenster Arch. [Maple, 1979] It is eroded in areas along the Red River-Electra and Muenster Arches to the north, the Llano uplift to the south where it outcrops, and the easternmost portion of the province where the Barnett laps onto the Eastern Shelf-Concho Platform.

Average total organic carbon (TOC) content in the Barnett Shale is about 4% and TOC is as high as 12% in samples from outcrops along the Llano uplift on the south flank of the Fort Worth Basin. [Henk et al., 2000; Jarvie et al., 2001] It has geochemical characteristics similar to other Devonian-Mississippian black shales found elsewhere in the US (e.g., Woodford, Bakken, New Albany, and Chattanooga Formations). These black shales all contain oil-prone organic matter (Type II kerogen) based on hydrogen indices above 350 milligrams of hydrocarbons per gram of TOC and generate a similar type of high quality oil (low sulfur, >30 API gravity). Although kerogen cracking decomposition is a source of oil and gas from the Barnett Shale, the principal source of gas in the Newark East Field is from cracking of oil and bitumen. [Jarvie et al., 2001]

Thermal maturity

Low maturation levels in the Barnett Shale at vitrinite reflectance (Ro), estimated at 0.6-0.7%, yields oils of 38° API gravity in Brown County. Oils found in Shackelford, Throckmorton, and Callahan Counties as well, as in Montague County, are derived from Barnett Shale at the middle of the zone of oil generation (oil window) thermal maturities levels (≈0.9% Ro). Although condensate is associated with gas production in Wise County, Barnett source rock maturity is generally 1.1% Ro or greater. The zone of wet gas generation is in the 1.1-1.4% Ro range, whereas the primary zone of dry gas generation (main gas window) begins at a Ro of 1.4%.

Thermal maturity of Barnett Shale can also be derived from TOC and Rock-Eval (Tmax) measurements. Although Tmax is not very reliable for high maturity kerogens due to poor pyrolysis peak yields and peak shape, the extent of kerogen transformation can be utilized. For example, Barnett Shale having a 4.5% TOC and a hydrogen index of less than 100 is in the wet or dry gas windows with equivalent Ro values greater than 1.1% TOC. In contrast, low maturity Barnett Shale from Lampasas County outcrops have initial TOC values averaging about 12% with hydrocarbon potentials averaging 9.85 % by volume. A good average value for Barnett Shale is derived from the Mitcham #1 well in Brown County where TOC is 4.2% and hydrocarbon potential is 3.37% by volume. Using these data we can determine TOC values will decrease 36% during maturation from the immature stage to the gas-generation window. Samples from the T. P. Simms well in the Newark East gas-producing area have average TOC values of 4.5%, but greater than 90% of the organic matter is converted to hydrocarbons. Thus, its original TOC was about 7.0% with an initial estimated potential of 5.64% by volume. Any oil generated would be expelled into shallow (or deeper) horizons as in the west and north, or cracked to gas where measured vitrinite reflectance is above 1.1% Ro.

Hydrocarbon generation

The Barnett Shale is thermally mature for hydrocarbon generation over most of its area. Barnett source rock is presently in the oil-generation window along the north and west parts of the province, and in the gas window on the east half of the Barnett-Paleozoic TPS. Expulsion of high-quality oil from the Barnett was episodic and began at low (Ro = 0.6%) thermal maturity. 32 oils from Wise and Jack Counties were analyzed to determine the characteristics of the generating source rock. API gravity and sulfur content were integrated with high-resolution gas chromatography (GC) and Gas chromatography-mass spectrometry (GCMS) analyses. The API gravity of the oils ranges from 35° to 62° and sulfur contents are low (<0.2%), which is characteristic of high thermal maturity oils. Biomarkers from GCMS analyses show oils were sourced from marine shale, based on sterane distribution and the presence of diasteranes. Carbon isotopic analyses of saturated and aromatic hydrocarbon fractions support hydrocarbon generation from a single-source unit. In the main gas-producing area of fractured Barnett Shale, the gas generation window is along a trend sub-parallel to the Ouchita thrust front. Jarvie (2001) reported the British Thermal Unit (BTU) content of Barnett gas is directly proportional to Ro levels.

Reservoir rocks

Reservoir rocks include clastic and carbonate rocks ranging in age from Ordovician to Early Permian. Most production from conventional reservoirs is from Pennsylvanian rocks, whereas the only recognized production from an unconventional accumulation is Mississippian-Pennsylvanian fractured Barnett Shale. Conglomerate of the Pennsylvanian Bend Group is the main producing reservoir at giant Boonsville Field with cumulative production through 2001 exceeding convert|3|Tcuft of gas. Oil sourced from Barnett Shale is produced from numerous reservoir rocks in the Bend Arch-Fort Worth Basin, including Barnett Shale, Caddo Formation, Canyon Group, Chappel Limestone, Bend Group,and Ellenburger Group.

eal rocks

Seal rocks in the Barnett-Paleozoic TPS are mostly shale units and dense, low permeability carbonate rock that are distributed on both regional and local scales. Barnett Shale is a major regional seal for older reservoirs, mostly porous carbonate rock reservoirs of the Ellenburger Group. Production from Barnett Shale is largely dependent on the presence or absence of Marble Falls and Viola limestones. Although these formations are not considered seal rocks in areas where they are tight and not water wet, they serve as barriers confining hydraulic-induced fracturing ("frac barriers") and help retain formation pressures during well stimulation. [Bowker, 2002; Shirley, 2002]

Traps

Traps for conventional hydrcocarbon accumulations are mostly stratigraphic for carbonate rock reservoirs and both structural and stratigraphic in clastic-rock reservoirs. Combination structural and stratigraphic traps are also common in Pennsylvanian sandstone reservoirs. Stratigraphic traps in carbonate rocks result from a combination of facies and depositional topography, erosion, updip pinchout of facies, and diagenetically controlled enhanced-permeability and porosity zones. A good example of a carbonate stratigraphic trap is the pinnacle reef traps of the Chappel Limestone, where local porous grainstone and packstone are restricted to isolated buildups or reef clusters on low-relief paleotopography of the eroded Ellenburger Group. Chappel pinnacle reefs are draped and sealed by the overlying Barnett Shale. Stratigraphic traps in Atoka Formation sandstones and conglomerates are mainly pinch outs related to facies changes or erosional truncation. Structural traps for Pennsylvanian sandstones and conglomerate reservoir rocks are mainly simple anticlines and fault-bounded anticlines.

Fractured Barnett Shale

High-quality (35-40° API gravity, low sulfur) oil is produced from Barnett Shale in the province’s north and western portions where it exhibits low thermal maturity (Ro ≈ 0.6%). Similar quality oils (40-50° API gravity), and condensates associated with gas are produced in Wise County where the Barnett is of higher thermal maturity. Gas production is from hydraulically-fractured black siliceous shale. Calorific values of gases from NE-F commonly range between 1,050-1,300 BTU. [Jarvie, 2002] The Barnett’s main producing facies is a black, organic-rich siliceous shale with a mean composition of about 45% quartz, 27% clay (mostly illite/smectite, and illite), 10% carbonate (calcite, dolomite, and siderite), 5% feldspar, 5% pyrite, and 5% TOC. [Lancaster et al., 1993; Henk et al., 2000] Average porosity in the productive portions is about 6% and matrix permeability is measured in nanodarcies. [Lancaster et al., 1993]

Three AUs have been proposed for the Barnett Shale continuous accumulations, each with different geologic and production characteristics:
# a NE-F gas “sweet spot” where the Barnett is siliceous, thick, within the gas generation window, slightly overpressured, and enclosed by dense, tight overlying Marble Falls Limestone and underlying Viola Limestone and Simpson Group as frac barriers;
# an outlying area where the Barnett is within the gas-generation window but the subcrop is the porous Ellenburger and the overlying Marble Falls Limestone barrier may be absent; and
# an area of lesser potential where overlying and underlying barriers may be absent and production includes oil and gas from fractured Barnett Shale. The siliceous nature of the Barnett Shale, and its relation to fracture enhancement in NE-F, was noted by Lancaster. Also, the second AU, where the Barnett Shale subcrop is Ellenburger Group carbonate rocks, is being tested by several operators. The unit’s resource potential unit will be guided by the results of current testing with directional wells and various completion methods to determine optimum completion techniques for gas recovery. [Bowker, 2002; Shirley, 2002]

Historically, estimated ultimate recoveries (EURs) for Barnett gas wells at NE-F increased with time, as follows:
#300 to 500 million cubic feet nowrap|(8.5 × 106 to 1.4 × 107 m3) of gas before 1990;
#600 to 1000 million cubic feet nowrap|(1.7 × 107 to 2.8 × 107 m3) of gas between 1990 and 1997; and
#800 to 1200 million cubic feet nowrap|(2.3 × 107 to 3.4 × 107 m3) of gas between 1998 and 2000.In 2002, Devon Energy reported the mean EUR for Newark East Barnett gas wells is convert|1.25|Gcuft of gas. The progressive increase in EUR in Barnett wells is the result of improved geologic and engineering concepts that guide development of the Barnett continuous gas play. Moreover, recompletion of wells after about five years of production commonly adds convert|759|Mcuft to its EUR. [Bowker, 2002; Shirley, 2002]

Notes

References


* [http://www.bseec.org Barnett Shale Energy Education Council]
* [http://www.rrc.state.tx.us/interactive_data.html Texas Railroad Commission Public Interactive Data]
*Abdel-Wahab, M. (1980) Stratigraphy of the Strawn (Pennsylvanian), Colorado River Valley, North-Central Texas, master’s thesis, University of Texas
*Allard, J. (2000) [http://www.landmand.org "Barnett Shale play hot in North Texas"]
*Ball, M. (1996) [http://geo-nsdi.er.usgs.gov/metadata/digital-data/30/boundary.faq.html "Province 045": USGS National Assessment of Oil and Gas resources]
*Ball, M. (1995) [http://certmapper.cr.usgs.gov/data/noga95/prov45/text/prov45.pdf Bend Arch-Fort Worth Basin Province (045)] USGS
*Bowker, K. (2002) [http://foundation.aapg.org/library/2003barnettshalesymp.pdf "Developments of Barnett Shale, Fort Worth Basin"] : Rocky Mountain Geologists & Petroleum Technology Transfer Council
*Devon Energy Corp. (2002) [http://www.dvn.com Mid-year Operations and Barnett Shale school]
*Flippin, J. (1982) "Stratigraphy, Structure, and Economic Aspects of Paleozoic strata, Erath County": Dallas Geological Society (DGS)
*Faust, L (1963) [http://scitation.aip.org/getabs/servlet/GetabsServlet?prog=normal&id=GPYSA7000028000006000990000001&idtype=cvips&gifs=yes The Fargo Field: A Case History] Geophysics, V. 28, Issue 6
*Gautier, D., [http://energy.cr.usgs.gov/energy/PubsPgs/DDS-30.html 1995 National assessment Oil and gas resources] : USGS DDS-30
*Hall, J. (2002) [http://www/dvn.com Barnett Shale geology] , in Devon Energy Corp.
*Jarvie, D. (2002) [http://www.humble-inc.com/abstract_aapg_ruidoso_barnett_shale.pdf "Barnett Shale as an analog for other black shales"] : AAPG Meeting, New Mexico.
*Jarvie, D. (2004) [http://www.humble-inc.com "Evaluation of Hydrocarbon Generation & Storage, Barnett Shale, Ft. Worth Basin"] Special BEG/PTTC Presentation
*Kerans, C. (1988) "Karst-controlled reservoir heterogeneity; Ellenburger Group Carbonates West Texas": AAPG Bulletin, v. 7
*Klett, T. (2000) [http://pubs.usgs.gov/dds/dds-060/ "Assessment hierarchy and initial province ranking"] , USGS World Petroleum Assessment
*Lancaster, D. (1993) "Research characterize Fort Worth Basin’s Barnett Shale": OGJ, v. 91
*Magoon, L. (2000) [http://pubs.usgs.gov/dds/dds-060/ "Natural fluid network constrains assessment unit"] , USGS World Assessment
*Mapel, W. (1979) "Paleotectonic investigations of the Mississippian System": USGS Paper 1010
*Pollastro, M. (2003) [http://www.searchanddiscovery.net/documents/pollastro/images/article.pdf Assessing Undiscovered Resources of the Barnett-Paleozoic TPS] USGS
*Schenk, C. (2001) [http://energy.cr.usgs.gov/oilgas/noga/ National Assessment of Oil & Gas Series] , USGS FS-113-01
*Schmoker, J. (1996) "Method for assessing continuous-type hydrocarbon accumulations": USGS DDS-30
*Shirley, K. (2002) "Barnett Shale living up to potential": AAPG Explorer, v. 23, no. 7
*Swindell, G. (2002) [http://gswindell.com/newark.htm Newark East Barnett Shale gas field, cumulative production graph]
*Walper, J. (1982) "Plate tectonic evolution of the Fort Worth Basin": DGS

ee also

*East Texas oil field
*Barnett Shale


Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • Foreland basin — basins, where accommodation space is generated by lithospheric extension. Types of Foreland BasinForeland basins can be divided into two categories: * Peripheral (Pro) foreland basins, which occur on the plate that is subducted or underthrust… …   Wikipedia

  • Marcellus Formation — Stratigraphic range: Middle Devonian …   Wikipedia

  • Denton, Texas — City of Denton   City   …   Wikipedia

  • Barnett Shale — Infobox Oil field name = Barnett Shale region = Bend Arch Fort Worth Basin,Texas country = United States coordinates = locblock = offonshore = Onshore operators = Devon, Chesapeake, EOG, XTO, Range Resources, EnCana, ConocoPhillips, Quicksilver,… …   Wikipedia

  • United States — a republic in the N Western Hemisphere comprising 48 conterminous states, the District of Columbia, and Alaska in North America, and Hawaii in the N Pacific. 267,954,767; conterminous United States, 3,022,387 sq. mi. (7,827,982 sq. km); with… …   Universalium

  • Permian High School — Address 1800 E. 42nd Street Odessa, TX, 79762 United States …   Wikipedia

  • Southwestern United States — Regional definitions vary from source to source. New Mexico and Arizona (in dark red) are almost always considered the core, modern day Southwest, while the striped states may or may not be considered to be part of the same region. California is… …   Wikipedia

  • National Register of Historic Places listings in Texas, Counties K-S — The following is a list of places within the state of Texas that are listed in the National Register of Historic Places. The names on the list are as they were entered in the register; some place names are inaccurate or have changed since being… …   Wikipedia

  • china — /chuy neuh/, n. 1. a translucent ceramic material, biscuit fired at a high temperature, its glaze fired at a low temperature. 2. any porcelain ware. 3. plates, cups, saucers, etc., collectively. 4. figurines made of porcelain or ceramic material …   Universalium

  • China — /chuy neuh/, n. 1. People s Republic of, a country in E Asia. 1,221,591,778; 3,691,502 sq. mi. (9,560,990 sq. km). Cap.: Beijing. 2. Republic of. Also called Nationalist China. a republic consisting mainly of the island of Taiwan off the SE coast …   Universalium

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”