Electronic filter


Electronic filter

Electronic filters are electronic circuits which perform signal processing functions, specifically intended to remove unwanted signal components and/or enhance wanted ones. Electronic filters can be:

*passive or active
*analog or digital
*discrete-time (sampled) or continuous-time
*linear or non-linear
*infinite impulse response (IIR type) or finite impulse response (FIR type)

The most common types of electronic filters are linear filters, regardless of other aspects of their design. See the article on linear filters for details on their design and analysis.

History

The oldest forms of electronic filters are passive analog linear filters, constructed using only resistors and capacitors or resistors and inductors. These are known as RC and RL single pole filters respectively. More complex multipole LC filters have also existed for many years and the operation of such filters is well understood with many books having been written about them.

Hybrid filters have also been made, typically involving combinations of analog amplifiers with mechanical resonators or delay lines. Other devices such as CCD delay lines have also been used as discrete-time filters. With the availability of digital signal processing, active digital filters have become common.

Classification by technology

Passive filters

Passive implementations of linear filters are based on combinations of resistors (R), inductors (L) and capacitors (C). These types are collectively known as "passive filters", because they do not depend upon an external power supply.

Inductors block high-frequency signals and conduct low-frequency signals, while capacitors do the reverse. A filter in which the signal passes through an inductor, or in which a capacitor provides a path to ground, presents less attenuation to low-frequency signals than high-frequency signals and is a "low-pass filter". If the signal passes through a capacitor, or has a path to ground through an inductor, then the filter presents less attenuation to high-frequency signals than low-frequency signals and is a "high-pass filter". Resistors on their own have no frequency-selective properties, but are added to inductors and capacitors to determine the "time-constants" of the circuit, and therefore the frequencies to which it responds.

At very high frequencies (above about 100 Megahertz), sometimes the inductors consist of single loops or strips of sheet metal, and the capacitors consist of adjacent strips of metal. These inductive or capacitive pieces of metal are called stubs.

The inductors and capacitors are the reactive elements of the filter. The number of elements determines the order of the filter. In this context, an LC tuned circuit being used in a band-pass or band-stop filter is considered a single element even though it consists of two components.

ingle element types

The simplest passive filters consist of a single reactive element. These are constructed of RC, RL, LC or RLC elements.

The quality or "Q" factor is a measure that is sometimes used to describe simple band-pass or band-stop filters. A filter is said to have a high "Q" if it selects or rejects a range of frequencies that is narrow in comparison to the centre frequency. "Q" may be defined as the ratio of centre frequency divided by 3dB bandwidth. It is not commonly employed with higher order filters where other parameters are of more concern.

L filter

Consists of two elements, one in series and one in parallel.

T filter

Three element filters in a 'T' configuration can be constructed for low-pass, high-pass, band-pass or band-stop.

π filter

Three element filters in a 'π' configuration can be constructed for low-pass, high-pass, band-pass or band-stop.

Multiple element types

Multiple element filters are usually constructed as a ladder network. These can be seen as a continuation of the L,T and π designs of filters. More elements are needed when it is desired to improve some parameter of the filter such as stop-band rejection or slope of transition from pass-band to stop-band.

Active filters

Active filters are implemented using a combination of passive and active (amplifying) components, and require an outside power source. Operational amplifiers are frequently used in active filter designs. These can have high "Q", and can achieve resonance without the use of inductors. However, their upper frequency limit is limited by the bandwidth of the amplifiers used.

Digital filters

Digital signal processing allows the inexpensive construction of a wide variety of filters. The signal is sampled and an analog to digital converter turns the signal into a stream of numbers. A computer program running on a CPU or a specialized DSP (or less often running on a hardware implementation of the algorithm) calculates an output number stream. This output can be converted to a signal by passing it through a digital to analog converter. There are problems with noise introduced by the conversions, but these can be controlled and limited for many useful filters. Due to the sampling involved, the input signal must be of limited frequency content or aliasing will occur. See also: Digital filter.

Other filter technologies

Quartz filters and piezoelectrics

In the late 1930s, engineers realized that small mechanical systems made of rigid materials such as quartz would acoustically resonate at radio frequencies, i.e. from audible frequencies (sound) up to several hundred megahertz.Some early resonators were made of steel, but quartz quickly became favored. The biggest advantage of quartz is that it is piezoelectric. This means that quartz resonators can directly convert their own mechanical motion into electrical signals. Quartz also has a very low coefficient of thermal expansion which means that quartz resonators can produce stable frequencies over a wide temperature range.
Quartz crystal filters have much higher quality factors than LCR filters. When higher stabilities are required, the crystals and their driving circuits may be mounted in a "crystal oven" to control the temperature. For very narrow band filters, sometimes several crystals are operated in series.

Engineers realized that a large number of crystals could be collapsed into a single component, by mounting comb-shaped evaporations of metal on a quartz crystal. In this scheme, a "tapped delay line" reinforces the desired frequencies as the sound waves flow across the surface of the quartz crystal.The tapped delay line has become a general scheme of making high-"Q" filters in many different ways.

AW filters

SAW (surface acoustic wave) filters are electromechanical devices commonly used in radio frequency applications. Electrical signals are converted to a mechanical wave in a piezoelectric crystal; this wave is delayed as it propagates across the crystal, before being converted back to an electrical signal by further electrodes. The delayed outputs are recombined to produce a direct analog implementation of a finite impulse response filter. This hybrid filtering technique is also found in an analog sampled filter.SAW filters are limited to frequencies up to 3 GHz.

BAW filters

BAW (Bulk Acoustic Wave) filters are electromechanical devices. BAW filters can implement ladder or lattice filters.BAW filters typically operate at frequencies from around 2 to around 16 GHz, and in may be smaller or thinner than equivalent SAW filters. Two main variants of BAW filters are making their way into devices, Thin film bulk acoustic resonator or FBAR and Solid Mounted Bulk Acoustic Resonators.

Garnet filters

Another method of filtering, at microwave frequencies from 800 MHz to about 5 GHz, is to use a synthetic single crystal yttrium iron garnet sphere made of a chemical combination of yttrium and iron (YIGF, or yttrium iron garnet filter). The garnet sits on a strip of metal driven by a transistor, and a small loop antenna touches the top of the sphere. An electromagnet changes the frequency that the garnet will pass. The advantage of this method is that the garnet can be tuned over a very wide frequency by varying the strength of the magnetic field.

Atomic filters

For even higher frequencies and greater precision, the vibrations of atoms must be used. Atomic clocks use caesium masers as ultra-high "Q" filters to stabilize their primary oscillators. Another method, used at high, fixed frequencies with very weak radio signals, is to use a ruby maser tapped delay line.

The transfer function

The transfer function H(s) of a filter is the ratio of the output signal Y(s) to that of the input signal X(s) as a function of the complex frequency s:

: H(s)=frac{Y(s)}{X(s)}with s = sigma + j omega.

The transfer function of all linear time-invariant filters generally share certain characteristics:

* Since the filters are constructed of discrete components, their transfer function will be the ratio of two polynomials in s, i.e. a rational function of s. The order of the transfer function will be the highest power of s encountered in either the numerator or the denominator.
* The polynomials of the transfer function will all have real coefficients. Therefore, the poles and zeroes of the transfer function will either be real or occur in complex conjugate pairs.
* Since the filters are assumed to be stable, the real part of all poles (i.e. zeroes of the denominator) will be negative, i.e. they will lie in the left half-plane in complex frequency space.

The proper construction of a transfer function involves the Laplace transform, and therefore it is needed to assume null initial conditions, because:mathcal{L}left{frac{df}{dt} ight} = scdotmathcal{L} left{ f(t) ight}-f(0), And when f(0)=0 we can get rid of the constants and use the usual expression:mathcal{L}left{frac{df}{dt} ight} = scdotmathcal{L} left{ f(t) ight}An alternative to transfer functions is to give the behavior of the filter as a convolution. The convolution theorem, which holds for Laplace transforms, guarantees equivalence with transfer functions.

Classification by transfer function

Filters may be specified by family and passband. A filter's family is specified by certain design criteria which give general rules for specifying the transfer function of the filter. Some common filter families and their particular design criteria are:

*Butterworth filter - no gain ripple in pass band and stop band, slow cutoff
*Chebyshev filter(Type I) - no gain ripple in stop band, moderate cutoff
*Chebyshev filter(Type II) - no gain ripple in pass band, moderate cutoff
*Bessel filter - no group delay ripple, no gain ripple in both bands, slow gain cutoff
*Elliptic filter - gain ripple in pass and stop band, fast cutoff
*Optimum "L" filter
*Gaussian filter - no ripple in response to step function
*Hourglass filter
*Raised-cosine filter

Generally, each family of filters can be specified to a particular order. The higher the order, the more the filter will approach the "ideal" filter. The ideal filter has full transmission in the pass band, and complete attenuation in the stop band, and the transition between the two bands is abrupt (often called brick-wall).

Here is an image comparing Butterworth, Chebyshev, and elliptic filters. The filters in this illustration are all fifth-order low-pass filters. The particular implementation -- analog or digital, passive or active -- makes no difference; their output would be the same.

As is clear from the image, elliptic filters are sharper than all the others, but they show ripples on the whole bandwidth.

Each family can be used to specify a particular pass band in which frequencies are transmitted, while frequencies in the stop band (i.e. outside the pass band) are more or less attenuated.

*Low-pass filter - Low frequencies are passed, high frequencies are attenuated.
*High-pass filter - High frequencies are passed, Low frequencies are attenuated.
*Band-pass filter - Only frequencies in a frequency band are passed.
*Band-stop filter - Only frequencies in a frequency band are attenuated.
*All-pass filter - All frequencies are passed, but the phase of the output is modified.

The family and passband of a filter completely specify the transfer function of a filter.The transfer function completely specifies the behavior of a linear filter, but not the particular technology used to implement it.In other words, there are a number of different ways of achieving a particular transfer function when designing a circuit. A particular pass band filter can be obtained by transformation of a prototype filter of that class.

Classification by topology

Electronic filters can be classified by the technology used to implement them.Filters using passive filter and active filter technology can be further classified by the particular electronic filter topology used to implement them.

Any given filter transfer function may be implemented in any electronic filter topology.

Some common circuit topologies are:

* Cauer topology - Passive
* Sallen Key topology - Active
* Multiple Feedback topology - Active
* State Variable Topology - Active
* Biquadratic topology biquad filter - Active

Classification by design methodology

Historically, linear analog filter design has evolved through three major approaches. The oldest designs are simple circuits where the main design criterion was the Q factor of the circuit. This reflected the radio receiver application of filtering as Q was a measure of the frequency selectivity of a tuning circuit. From the 1920s filters began to be designed from the image point of view, mostly being driven by the requirements of telecommunications. After World War II the dominant methodology was network synthesis. The higher mathematics used originally required extensive tables of polynomial coefficient values to be published but modern computer resources have made that unnecessary. [Bray, J, "Innovation and the Communications Revolution", Institute of Electrical Engineers"]

Direct circuit analysis

Low order filters can be designed by directly applying basic circuit laws such as Kirchoff's laws to obtain the transfer function. This kind of analysis is usually only carried out for simple filters of 1st or 2nd order.

Image impedance analysis

:main|Composite image filtersThis approach analyses the filter sections from the point of view of the filter being in an infinite chain of identical sections. It has the advantages of simplicity of approach and the ability to easily extend to higher orders. It has the disadvantage that accuracy of predicted responses rely on filter terminations in the image impedance, which is usually not the case.Matthaei, Young, Jones "Microwave Filters, Impedance-Matching Networks, and Coupling Structures" McGraw-Hill 1964]

Network synthesis

:main article|Network synthesis filtersThe network synthesis approach starts with a required transfer function and then expresses that as a polynomial equation of the input impedance of the filter. The actual element values of the filter are obtained by continued-fraction or partial-fraction expansions of this polynomial. Unlike the image method, there is no need for impedance matching networks at the terminations as the effects of the terminating resistors are included in the analysis from the start.

See also

*Active filter
*ADSL broadband filter
*Analog filter
*Audio crossover
*Audio filter
*Cascaded integrator-comb filter
*Comb filter
*Digital filter
*Image filters
*Linear filter
*Non-linear filter
*Network synthesis filters
*Passive filter
*Q factor
*Resonance
*RF and microwave filter
*Spurline
*Switched-capacitor filter
*Tone control circuits
*Voltage-controlled filter

External links and references

:*cite book|author=Zverev, Anatol, I|year=1969|title=Handbook of Filter Synthesis|publisher=John Wiley & Sons|id=ISBN 0-471-98680-1 Catalog of passive filter types and component values. The Bible for practical electronic filter design.:*cite book|author=Williams, Arthur B & Taylor, Fred J|title=Electronic Filter Design Handbook|publisher=McGraw-Hill|year=1995|id=ISBN 0-07-070441-4 :* [http://www.national.com/an/AN/AN-779.pdf National Semiconductor AN-779] application note describing analog filter theory:* [http://www.vias.org/feee/filters_02.html Fundamentals of Electrical Engineering and Electronics] - Detailed explanation of all types of filters:* [http://www.lss.supelec.fr/Internet_php/pdf/GDROndes-Nov05-GT4-Kerherve.pdf#search=%22baw%20filter%22 BAW filters (in French; PDF)] :* [http://www.ieee.li/pdf/viewgraphs_filter_design_configurations.pdf Some Interesting Filter Design Configurations & Transformations] :* [http://www.rfzone.org/free-rf-ebooks/ Books and tutorials how to design RF Filters] :* [http://www.dspguide.com/ch3/4.htm Analog Filters for Data Conversion]

Wikimedia Foundation. 2010.

Look at other dictionaries:

  • electronic filter — elektroninis filtras statusas T sritis automatika atitikmenys: angl. electronic filter vok. elektronisches Filter, n rus. электронный фильтр, m pranc. filtre électronique, m …   Automatikos terminų žodynas

  • Electronic filter topology — An elementary filter topology introduces a capacitor into the feedback path of an op amp to achieve an unbalanced active implementation of a low pass transfer function Electronic filter topology defines electronic filter circuits without taking… …   Wikipedia

  • Filter — may refer to: Chemistry, engineering and materials In chemistry, engineering, or household usage, a device to separate mixtures. See: * Filter (chemistry) * Water filter * Air filter * Oil filter * Pneumatic filter Optics and photography In… …   Wikipedia

  • Electronic oscillator — An electronic oscillator is an electronic circuit that produces a repetitive electronic signal, often a sine wave or a square wave.A low frequency oscillator (LFO) is an electronic oscillator that generates an AC waveform between 0.1 Hz and 10 Hz …   Wikipedia

  • Filter (optics) — Coloured and Neutral Density filters Optical filters are devices which selectively transmit light of different wavelengths, usually implemented as plane glass or plastic devices in the optical path which are either dyed in the mass or have… …   Wikipedia

  • Electronic paper — Electronic paper, also called e paper, is a display technology designed to mimic the appearance of ordinary ink on paper. Unlike a conventional flat panel display, which uses a backlight to illuminate its pixels, electronic paper reflects light… …   Wikipedia

  • Electronic engineering — is a discipline dealing with the behavior and effects of electrons (as in electron tubes and transistors) and with electronic devices, systems, or equipment.The term now also covers a large part of electrical engineering degree courses as studied …   Wikipedia

  • Electronic voice phenomenon — Electronic voice phenomena (EVP) are sections of static noise on the radio or electronic recording that some listeners believe sound like voices speaking words; paranormal investigators sometimes interpret these noises as the voices of ghosts or… …   Wikipedia

  • Electronic Music Studios — (EMS) ist ein eingetragenes Warenzeichen des ersten englischen Synthesizer Studios. Gegründet wurde das Studio von Peter Zinovieff. 1969 präsentierte die Firma mit dem Synthesizer VCS 3 den ersten preisgünstigen und zugleich portablen Analog… …   Deutsch Wikipedia

  • Electronic counter-countermeasures — (ECCM) describes a variety of practices which attempt to reduce or eliminate the effect of Electronic countermeasures (ECM) on electronic sensors aboard vehicles, ships and aircraft and weapons such as missiles. ECCM is also known as Electronic… …   Wikipedia


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.