Shaft-driven bicycle

Shaft-driven bicycle

A shaft-driven bicycle is a chainless bicycle that uses a driveshaft instead of a chain to transmit power from the pedals to the wheel. Shaft drives were introduced over a century ago, but were mostly supplanted by chain-driven bicycles due to the gear ranges possible with sprockets and derailleurs. Recently, due to advancements in internal gear technology, a small number of modern shaft-driven bicycles have been introduced.

Shaft-driven bikes have a large bevel gear where a conventional bike would have its chainring. This meshes with another bevel gear mounted on the driveshaft. The use of bevel gears allows drive from the pedals to be turned through 90 degrees. The driveshaft then has another bevel gear near the rear wheel hub which meshes with a bevel gear on the hub where the rear sprocket would be on a conventional bike. The 90-degree change of the drive plane that occurs at the bottom bracket and again at the rear hub requires the use of bevel gears. Bevel gears are the most efficient way of turning drives 90 degrees as compared to worm gears or crossed helical gears.The driveshaft is often mated to a hub gear which is an internal gear system housed inside the rear hub. Today, there are three significant manufacturers of internal hubs suitable for use with shaft drive systems, including Shimano Nexus, SRAM and Sturmey-Archer.

Comparison of shaft vs chain driven bicycles

A valid comparison of shaft vs. chain drives can only be made if both bikes use the same type of gearing, whether single-speed or with an internal gear system. Most of the advantages claimed for a shaft drive can be realized by using a fully-enclosed chain case.

Advantages

*Compactness: The driveshaft and bevel gears take up less volume than an enclosed chain.
*Ground clearance: The driveshaft system allows greater ground clearance.
*Enclosed drive system: The driveshaft and gearing are enclosed which protects moving parts from the elements.
*Safety: There is no danger of clothing or fingers being drawn into the chain and sprockets.
*Cleanliness: Because a bicycle chain needs to be lubricated, usually with oil, a chain driven bicycle can stain its rider's clothing and hands.
*Consistency of performance: Shaft drives operate at a very consistent rate of efficiency and performance, without adjustments or maintenance.
*Suitability to longer drive trains: The shaft-driven system is particularly suitable to many recumbent applications where there is a long distance from the crankset to the driven rear wheel. Maintaining chain tension is often difficult for these applications. Also, the chain line may not be straight, necessitating the use of extra jockey wheels. A drive shaft can relatively easily turn through these slight angles with the use of a universal joint.
*Longevity: The driveshaft keeps its performance stable for almost any length of time, whereas a chain deteriorates, and chain as well as sprockets have to be replaced.
*Reduced maintenance and repair: Because a driveshaft is fully enclosed, it is less susceptible to damage and does not require adjustments or cleaning like chains.

Disadvantages

*Power loss: A shaft-driven system is less efficient than a well maintained chain-driven system. Shaft driven systems are often quoted as being "95% efficient", while chain driven systems are quoted as "98% efficient".
*Complexity: Though the shaft-driven system seems simple on the outside, the manufacture of the necessary bevel gears is complex compared to that of a chain and sprockets.
*Cost: Due to the manufacturing complexity of the frame and shaft drive, the manufacturing cost is typically higher.
*Gear range: Internal hub geared bikes typically have a more restricted gear range than comparable derailleur-equipped bikes, and have fewer ratios within that range (an issue because a rider typically prefers to pedal within a fairly narrow cadence band).
*Weight: A shaft-driven bicycle typically weighs about one pound (500 grams) more than an equivalent chain-driven bicycle.
*Changing a flat: shaft drives are typically more complex to disassemble when repairing punctures.

Some of the other issues addressed by the shaft drive, such as protection for clothing and from ingress of dirt, can be met through the use of chain guards. The reduced need for adjustment in shaft-drive bikes also applies to a similar extent in chain drive hub geared bikes. Not all hub gear systems are shaft compatible.

Bicycles typically employ more torque (an adult man can easily generate more than 100 lb/f) but at much lower rotational speed than motorcycles and cars [http://yarchive.net/bike/shaft_drive.html] . This mitigates against shaft drive as the shafts must be large to cope with the torque, which adds to their mass. This is particularly noticeable when pedalling hard, when there can be noticeable torsional springing in the drive train.

Past and present

The shaft-driven bicycle was originally developed in the late 1800s. The French company L'Acatane did most of the development in the 1890s. During this period, Columbia aggressively marketed the chainless bicycle in the USA. Chainless bicycles were moderately popular in 1898 and 1899, although sales were still much smaller than regular bicycles, primarily due to the high cost. The bikes were also somewhat less efficient than regular bicycles -- there was roughly an 8 percent in the gearing, in part due to limited manufacturing technology at the time (although the efficiency loss was not huge -- Major Taylor won several races on a shaft drive bicycle). The rear wheel was also more difficult to remove to change flats. Many of these deficiencies have been overcome in the past century.

While a small number of chainless bicycles were available, for the most part, shaft-driven bicycles disappeared from view for most of the 20th century. There is, however, still a niche market for chainless bikes, especially for commuters, and there are a number of manufacturers who offer them either as part of a larger range or as a primary specialisation.

References

See also

* Velovision magazine regularly reviews shaft-drive bikes.

External links

* [http://www.tomagbabi.pwp.blueyonder.co.uk/images/schematic_large.jpgSchematic of drive system]
* [http://www.kenkifer.com/bikepages/touring/gears.htm Detailed discussion on gearing]
* [http://motos.home.att.net/bicycle.htm Drive Shaft Bicycle Web Page]
* [http://www.shaftdrive.com.tw Giovelli's "Shaft-Drive" system]


Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • Bicycle — For other uses, see Bicycle (disambiguation). A mountain bike, a popular multi use bicycle. A bicycle, also known as a bike, pushbike or cycle, is a human powered, pedal driven, single track vehicle, having two wheels attached to a frame, one… …   Wikipedia

  • Bicycle gearing — The gearing on a bicycle is the selection of appropriate gear ratios for optimum efficiency or comfort. Different gears and ranges of gears are appropriate for different people and styles of cycling. Multi speed bicycles allow gear selection to… …   Wikipedia

  • Drive shaft — This article is about the mechanical device. For the fictional music group from the American television series Lost , see Charlie Pace. Not to be confused with Axle. Drive shaft with universal joints at each end and a spline in the centre A drive …   Wikipedia

  • List of bicycle types — This list gives an overview of different types of bicycles, categorized by function (racing, recreation, etc); number of riders (one, two, or more); by construction or frame type (upright, folding, etc); by gearing (single speed, derailleur gears …   Wikipedia

  • Chainless bicycle — A chainless bicycle is a bicycle that transmits power to the driven wheel through a mechanism other than a metal chain. Examples: Directly driven ordinary bicycle (see Penny farthing) Shaft driven bicycle Belt driven bicycle Hydraulic bicycle… …   Wikipedia

  • Motorized bicycle — A VéloSoleX motorized bicycle A motorized bicycle, motorbike, cyclemotor, or vélomoteur is a bicycle with an attached motor and transmission used either to power the vehicle unassisted, or to assist with pedaling. Since it always retains both… …   Wikipedia

  • Raleigh Bicycle Company — The Raleigh Bicycle Company is a bicycle manufacturer originally based in Nottingham. It is one of the oldest bicycle companies in the world. From 1929 to 1935 Raleigh also produced motorcycles and three wheel cars, leading to the formation of… …   Wikipedia

  • Continuously variable transmission — Transmission types Manual Sequential manual Non synchronous Preselector Automatic Manumatic Semi automatic Electrohydraulic Dual …   Wikipedia

  • Freewheel — For information about the bicycle component, see Cogset. Freewheel mechanism …   Wikipedia

  • Transmission (mechanics) — Gearbox redirects here. For the video game developer, see Gearbox Software. 5 speed gearbox + reverse, the 1600 Volkswagen Golf (2009). A machine consists of a power source and a power transmission system, which provides controlled application of …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”