Allen Telescope Array

Allen Telescope Array
Allen Telescope Array
The Allen Telescope Array (ATA-42), October 11, 2007.
The Allen Telescope Array (ATA-42), October 11, 2007
Organization SETI Institute & Radio Astronomy Laboratory
Location Hat Creek Radio Observatory
Coordinates Coordinates: 40°49′01″N 121°28′12″W / 40.817°N 121.470°W / 40.817; -121.470

The Allen Telescope Array (ATA), formerly known as the One Hectare Telescope (1hT), was a joint effort by the SETI Institute and the Radio Astronomy Laboratory (RAL) at the University of California, Berkeley to construct a radio interferometer that is dedicated to astronomical observations and a simultaneous search for extraterrestrial intelligence.[1][2]

The ATA is under construction at the Hat Creek Radio Observatory, 290 miles (470 km) northeast of San Francisco, California. When completed, the array is expected to consist of 350 antennas.[3] The first phase with 42 antennas (ATA-42) is complete and became operational on 11 October 2007.[4][5] However, in April 2011, the ATA was placed in operational hibernation due to funding shortfalls.[6][7] In August 2011, short-term funding was found [8]



First conceived by SETI pioneer Frank Drake, the idea has been a dream of the SETI Institute for years. However, it was not until early 2001 that research and development commenced after a donation of $11.5 million by the Paul G. Allen Family Foundation. In March 2004, following successful completion of a three-year research and development phase, the SETI Institute unveiled a three-tier construction plan for the telescope. Construction began right after, due to the pledge of $13.5 million by Paul Allen (co-founder of Microsoft) to support the construction of the first and second phases. The SETI Institute named the telescope in his honor. Overall Paul Allen has contributed more than $30 million to the project.


The ATA will be a centimeter-wave array that pioneers the Large-Number Small-Diameter concept of building radio telescopes. Compared to a large dish antenna, large numbers of smaller dishes are cheaper for the same collecting area. However, to get similar sensitivity, the signals from all telescopes must be combined. This requires high performance electronics, and has been prohibitively expensive until now. However, due to the declining cost of the electronic components, the required electronics are now practical, resulting in a large cost saving over telescopes of more conventional design. This is informally referred to as "replacing steel with silicon".

The ATA has four primary advantages for scientific studies over all major radio telescopes built to date: a very wide field of view (2.45° at λ = 21 cm), complete instantaneous frequency coverage from 0.5 to 11.2 GHz, multiple simultaneous backends, and active interference mitigation. The instantaneous area of sky imaged is 17 times that of the Very Large Array. The instantaneous frequency coverage of more than four octaves is unprecedented in radio astronomy and is the result of a unique feed, input amplifier, and signal path design. Active interference mitigation will make it possible to observe even at the frequencies of many terrestrial radio emitters.

Because all-sky surveys are an important part of the science program, the efficiency of the ATA will be increased by doing radio astronomy and SETI searches simultaneously. The telescope will do this by splitting the signals in the control room prior to final processing. Simultaneous observations are possible because for SETI, several target stars will lie within the large field of view afforded by the 6m dishes wherever the telescope is pointed. Thus, by agreement between the RAL and the SETI Institute, the needs of conventional radio astronomy will determine the pointing of the array.

The ATA is planned to comprise 350 six-meter dishes and will make possible large, deep radio surveys that were not previously feasible. The telescope design incorporates many new features, including hydroformed antenna surfaces, a log-periodic feed covering the entire range of frequencies from 500 MHz to 11.2 GHz, and low-noise, wide-band amplifiers with a flat response over the entire band making it possible to amplify the sky signal directly. This amplified signal, containing the entire received bandwidth, is brought from each antenna to the processing room on optical fiber cables. This means that as electronics improve and wider bandwidths are feasible, only the central processor needs to change, and not the antennas or feeds.

The instrument will be operated and maintained by the Radio Astronomy Laboratory. The RAL has worked hand in hand with the SETI Institute during design and prototyping and is the primary designer of the feed, antenna surfaces, beam forming, correlator and imaging system for radio astronomy observations.

The astronomy decadal panel, Astronomy and Astrophysics in the New Millennium, endorsed SETI and recognized the ATA (then called the 1-Hectare Telescope) as an important stepping stone to the Square Kilometer Array (SKA).

The ATA aspires to be among the world's largest and fastest observing instruments. It will also permit astronomers to search for many different target stars simultaneously. When completed as originally envisioned, it will be one of the largest and most powerful telescopes in the world.

Although cost estimates of unbuilt projects are always dubious, and the specs are not identical (the conventional telescopes have lower noise temperature, but the ATA has a larger field of view, for example), the ATA has potential promise as a much cheaper radio telescope technology for a given effective aperture. For example, the amount spent on the first ATA-42 phase, including technology development, is roughly 1/3 of the cost of a new copy of a Deep Space Network 34 meter antenna of similar collecting area.[9] Similarly, the estimated total cost of building the remaining 308 dishes is estimated (as of October 2007) at about $41 million.[4] This is about a factor of 2 cheaper than the $85 million cost of the last large radio astronomy antenna built in the USA, the Green Bank Telescope, of similar collecting area. The contractor filed for a $29 million overrun, but only $4 million of this was allowed.[10]


Since its inception, the ATA has been a development tool for array technology (specifically, for the Square Kilometer Array). Future progress depends on the technical performance of the sub-array already under construction, and the procurement of additional funding.

The ATA was originally planned to be constructed in four stages, the ATA-42, ATA-98, ATA-206, and ATA-350; each number representing the number of dishes in the array at a given time (See Table 1).

Regular operations with 42 dishes started on 11 October 2007.[4] Funding for building additional antennas is currently being sought by the RAL from various sources, including the US Navy, DARPA, NSF and private donors.

Astronomical data has been acquired since May 2005, utilizing a four-input correlator (four antennas, dual polarization) and then updated in January 2007 with two eight-input (16 antennas, dual polarization).[11] Scientifically useful data has been acquired and is helping commission the array.[12]

Correlator development continues, with deployment of one 32-input correlator in June 2007 and utilized as eight individual correlators with eight dual-polarization inputs each.

Beam-forming electronics utilizing the BEE2 were deployed in June 2007 and are currently (08 Nov 2007) being integrated into the system to allow for simultaneous astronomical and SETI observations.[13] As of April 2008, the first pulsar observations have been conducted using the beamformer and a purpose-built pulsar spectrometer.[14]

In May 2009, UC Berkeley announced it was performing all-sky surveys using the Allen Telescope Array.[15]

The ATA Team reported initial results from their survey of the Galactic Center Region at the June 2009 meeting of the American Astronomical Society (AAS Meeting #214).[16]

As of April 2011, the ATA has been placed in hibernation mode due to funding shortfalls, meaning that it is no longer available for use.[17]

Key science goals

The science goals listed here represent the goals of the most important projects that will be conducted over the next three years with the ATA. Each of these goals is associated with one of the 4 stages of development (see Table 1). The bulleted items are the projects that will be undertaken and the subtopics are some of the science that will be produced. The ATA will:

  • Determine the HI content of galaxies out to z ∼ 0.2 over 3π steradians, to measure how much intergalactic gas external galaxies are accreting; to search for dark, starless galaxies; to lay the foundation for SKA dark energy detection
  • Classify 250,000 extragalactic radio sources as active galactic nuclei or starburst galaxies, to probe and quantify star formation in the local Universe; to identify high redshift objects; to probe large scale structure in the Universe; to identify gravitational lens candidates for dark matter and dark energy detection
  • Explore the transient sky, to probe accretion onto black holes; to find orphan gamma ray burst afterglows; to discover new and unknown transient phenomena
  • Survey 1,000,000 stars for SETI emission with enough sensitivity to detect an Arecibo radar out to 300 pc within the range of 1 and 10 GHz
  • Survey the 4×1010 stars of the inner galactic plane from 1.42 to 1.72 GHz for very powerful transmitters
  • Measure the magnetic fields in the Milky Way and other Local Group galaxies, to probe the role of magnetic fields in star formation and galaxy formation and evolution
  • Detect the gravitational wave background from massive black holes through pulsar timing
  • Measure molecular cloud and star formation properties using new molecular tracers, to map the star formation conditions on the scale of entire giant molecular clouds (GMCs); to determine the metallicity gradient of the Milky Way
Table 1: Array performance and key science projects
Array Status Beam size (arcsec) Srms (mJy) Speed (deg²s−1) Key science
ATA-42 Dish construction complete; commissioning in progress with 32 input, dual polarization (64 total inputs) correlator. 245 x 118 0.54 0.02 FiGSS: 5 GHz Continuum Survey, Galactic Plane Molecular Spectroscopy, SETI Galactic Center Survey
ATA-98 Awaiting results ATA-42 for funding 120 x 80 0.2s 0.11 ATHIXS† Trial Surveys, HI Stellar Outflows Survey, SETI Targeted Survey: 100 stars
ATA-206 TBD 75 x 65 0.11 0.44 ATHIXS, Map The Magnetized Galactic ISM, Pulsar Timing Array, Deep continuum and transient surveys, SETI Targeted Surveys
ATA-350 TBD 77 x 66 0.065 1.40 ATHIXS, Map The Magnetized Galactic ISM, Pulsar Timing Array Deep continuum and transient surveys, SETI Targeted Surveys
Note. Beam size and continuum sensitivity (Srms are estimated for a 6 minute, 100 MHz continuum snapshot observation at transit of a source at 40° declination at a wavelength of 21 cm. Speed is given for a survey at 21 cm observations with a bandwidth of 100 MHz that reaches 1 mJy rms.

ATHIXS is an all-sky deep HI extragalactic HI survey.

Opportunistic science

After array construction, a few science goals that were not explicitly designed have been mentioned.

For a very different science goal, the Allen Telescope Array has offered to provide the downlink for any contestants in the Google Lunar X Prize.[18] This is practical since the array, with no modifications, covers the main space communications bands (S-band and X-band). A telemetry decoder would be the only needed addition.

Also, the ATA was mentioned as a candidate for searching for a new type of radio transient.[19] It is an excellent choice for this because of a large field of view and wide instantaneous bandwidth. Following this suggestion, an instrument was custom-built for the ATA to search for bright radio transients, and observations were carried out between February and April 2008.[20]

Instrument details

The ATA Offset Gregorian Design

The ATA-42 configuration will provide a maximum baseline of 300 m (and ultimately the ATA-350, 900 m). A cooled log-periodic feed on each antenna is designed to provide a system temperature of ~45K from 1 GHz to 10 GHz, with reduced sensitivity in the range 0.5 GHz to 1.0 GHz and 10 GHz to 11.2 GHz. Four separate frequency tunings (IFs) are available to produce 4x100 MHz intermediate frequency bands. Two IFs support correlators for imaging; two will support SETI observing. All tunings can produce four dual polarization phased array beams which can be independently pointed within the primary beam and can be used with a variety of detectors. The ATA can therefore synthesize up to 32 phased array beams.

The wide field of view of the ATA gives it an unparalleled capability for large surveys (Fig. 4). The time required for mapping a large area to a given sensitivity is proportional to (ND)2, where N is the number of elements and D is the diameter of the dish. This leads to the surprising result that a large array of small dishes can outperform an array with smaller number of elements but considerably greater collecting area at the task of large surveys. As a consequence, even the ATA-42 is competitive with much larger telescopes in its capability for both brightness temperature and point-source surveys. For point source surveys, the ATA-42 is comparable in speed with Arecibo and the Green Bank Telescope (GBT), but slower by a factor of 3 than the Very Large Array (VLA). The ATA-350, on the other hand, will be an order of magnitude faster than the Very Large Array for point-source surveys and is comparable to the Expanded VLA (EVLA) in survey speed. For surveys to a specified brightness temperature sensitivity, the ATA-98 will exceed the survey speed of even the VLA-D configuration. The ATA-206 should match the brightness temperature sensitivity of Arecibo and the GBT. The ATA, however, provides better resolution than either these single dish telescopes.

The antennae for the ATA are 6.1 m × 7.0 m hydroformed offset Gregorian telescopes, each with a 2.4-meter subreflector with an effective f/D of 0.65. (DeBoer, 2001). The offset geometry eliminates blockage, which increases the efficiency and decreases the sidelobes. It also allows for the large subreflector, providing good low frequency performance. The hydroforming technology used to make these surfaces is the same hydroforming technique used to generate low-cost satellite reflectors by Andersen Manufacturing of Idaho Falls, Idaho. The unique, interior frame rim-supported compact mount allows excellent performance at a low cost. The drive system employs a spring-loaded passive anti-backlash azimuth drive train.

See also


  1. ^ Daniel Terdiman (12 December 2008). "SETI's large-scale telescope scans the skies". CNET News. Retrieved 2008-12-12. 
  2. ^ John Johnson, Jr. (1 June 2008). "Aliens get a new switchboard: a SETI radio telescope in Northern California". The Los Angeles Times.,0,1621324.story. Retrieved 2008-09-29. 
  3. ^
  4. ^ a b c Dennis Overbye (11 October 2007). "Stretching the Search for Signs of Life". The New York Times. Retrieved 2009-04-14. 
  5. ^ Staff writers (12 October 2007). "Skies to be swept for alien life". BBC News. Retrieved 2007-10-12. 
  6. ^ Hardy, Michael (2011-04-29). "Federal Computer Week". Retrieved 2011-09-19. 
  7. ^
  8. ^
  9. ^ Shannon McConnell (2005). "Deep Space Network Adds a 34m Beam Wave Guide Antenna in Madrid, Spain". Deep Space Network Home. JPL. Retrieved 2009-04-14. 
  10. ^ Senior Review Committee (22 October 2006) (PDF). From the Ground UP: Balancing the NSF Astronomy Program. National Science Foundation Division of Astronomical Sciences. p. Retrieved 2009-04-14. 
  11. ^ W.L. Urry, M. Wright, M. Dexter, D. MacMahon (16 February 2007) (PDF). The ATA Correlator ATA Memo 73. University of California, Berkeley. p. 3. Retrieved 2009-04-14. 
  12. ^ "GRB 070612A: Allen Telescope Array Observations". Retrieved 2011-09-19. 
  13. ^ "BEE2: A modular, scalable FPGA-based computing platform". Retrieved 2011-09-19. 
  14. ^ "Berkeley ATA Pulsar Processor (BAPP)". Center for Astronomy Signal Processing and Electronics Research (CASPER). University of California, Berkeley. 29 December 2008. Retrieved 2009-04-14. 
  15. ^ "Allen Telescope Array beings all-sky surveys". Retrieved 2011-09-19. 
  16. ^ Results from the Allen Telescope Array: SETI Survey of the Galactic Center Region [1]
  17. ^ John Matson (24 April 2011). "Budget crunch mothballs telescopes built to search for alien signals". Scientific American. Retrieved 2011-04-25. 
  18. ^ "Google Sponsors Lunar X PRIZE to Create a Space Race for a New Generation" (Press release). X PRIZE Foundation and Google Inc.. 13 September 2007. Retrieved 2009-04-14. 
  19. ^ Phil Berardelli (27 September 2007). "Big Radio from the Stars". ScienceNOW. Retrieved 2009-04-14. 
  20. ^ "ATA "Fly's Eye" Pulse Finder". Center for Astronomy Signal Processing and Electronics Research (CASPER). University of California, Berkeley. 29 December 2008.'s_Eye%22_Pulse_Finder. Retrieved 2009-11-08. 

External links

Wikimedia Foundation. 2010.

Look at other dictionaries:

  • Allen Telescope Array — Das Hat Creek Radioobservatorium ist eine vom Radio Astronomy Laboratory der University of California, Berkeley betriebene Radiosternwarte in Kalifornien, etwa 500 km nordöstlich von San Francisco in 1280 m Höhe gelegen. Inhaltsverzeichnis 1 85… …   Deutsch Wikipedia

  • Allen Telescope Array — Антенная решётка Аллена Комплекс ATA, в представлении художника …   Википедия

  • Allen Telescope Array — Pour les articles homonymes, voir ATA. Allen Telescope Array …   Wikipédia en Français

  • Allen Telescope Array — El Allen Telescope Array (en inglés Matriz de Telescopios Allen , también abreviado como ATA) representa el esfuerzo conjunto del Instituto SETI y el Laboratorio de Radioastronomía de la Universidad de California, Berkeley para construir un… …   Wikipedia Español

  • Telescope spatial — Télescope spatial Le télescope spatial Hubble en orbite autour de la Terre. Un télescope spatial est un télescope placé au delà de l atmosphère. Le télescope spatial présente l avantage par rapport à son homologue terrestre de ne pas être… …   Wikipédia en Français

  • Téléscope spatial — Télescope spatial Le télescope spatial Hubble en orbite autour de la Terre. Un télescope spatial est un télescope placé au delà de l atmosphère. Le télescope spatial présente l avantage par rapport à son homologue terrestre de ne pas être… …   Wikipédia en Français

  • Télescope spatial — Le télescope spatial Hubble en orbite autour de la Terre. Un télescope spatial est un télescope placé au delà de l atmosphère. Le télescope spatial présente l avantage par rapport à son homologue terrestre de ne pas être perturbé par l atmosphère …   Wikipédia en Français

  • One Hectare Telescope — Allen Telescope Array Pour les articles homonymes, voir ATA. Allen Telescope Array …   Wikipédia en Français

  • Square Kilometre Array — Künstlerische Darstellung des Zentrums der Antennenschüsseln Das Square Kilometre Array (kurz SKA) ist ein in Entwicklung befindliches Radioteleskop, welches eine totale Sammelfläche von ungefähr einem Quadratkilometer aufweisen wird.[1] Es wird… …   Deutsch Wikipedia

  • Atacama Large Millimeter Array — Atacama Large Millimeter/submillimeter Array ALMA logo Organisation Multi national Location Llano …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.