Oil pump (internal combustion engine)

Oil pump (internal combustion engine)
Oil circulation system
Gerotor type oil pump from a scooter engine

The oil pump in an internal combustion engine circulates engine oil under pressure to the rotating bearings, the sliding pistons and the camshaft of the engine. This lubricates the bearings, allows the use of higher-capacity fluid bearings and also assists in cooling the engine.

As well as its primary purpose for lubrication, pressurized oil is increasingly used as a hydraulic fluid to power small actuators. One of the first notable uses in this way was for hydraulic tappets in camshaft and valve actuation. Increasingly common recent uses may include the tensioner for a timing belt or variators for variable valve timing systems.

Contents

Pumps

The type of pump used varies. Gear pumps[1][2] trochoid pumps[3] and vane pumps[note 1] are all commonly used. Plunger pumps have been used in the past, but these are now only used rarely, for small engines.

To avoid the need for priming, the pump is always mounted low-down, either submerged or around the level of the oil in the sump. A short pick-up pipe with a simple wire-mesh strainer reaches to the bottom of the sump.

Pump drive

For simplicity and reliability, mechanical pumps are used, driven by mechanical geartrains from the crankshaft. Reducing pump speed is beneficial[note 2] and so it is usual to drive the pump from the cam (if this is mounted in the cylinder block) or distributor shaft, which turns at half engine speed. Placing the oil pump low-down uses a near-vertical drive shaft, driven by helical skew gears from the camshaft. Some engines, such as the Fiat twin cam engine of 1964, began as OHV engines with an oil pump driven from a conventional camshaft in the cylinder block. When the twin overhead cam engine was developed, the previous oil pump arrangement was retained and the camshaft became a shortened stub shaft. Even when the distributor position was moved from the previous block-mount to being mounted on the cylinder head camshafts, the oil pump drive remained in the same position, the unused distributor position now covered by a blanking plate.[4] Small engines, or scooters may have internal gear pumps mounted directly on their crankshaft.

For reliability, it is rare to use an external drive mechanism, either a separate belt drive or external gears, although camshaft-driven pumps often rely on the same timing belt. Additional separate belts are sometimes used where dry sump pumps have been added to engines during tuning.

Electric oil pumps are not used, again for reliability. Some "turbo timer" electric auxiliary oil pumps are sometimes fitted to turbocharged engines. These are a second oil pump that continues to run after the engine has stopped, providing cooling oil to the hot bearings of a turbocharger for some minutes, whilst it cools down.[note 3] These are supplementary pumps and do not replace the main, mechanical, oil pump.

Lubricating system

The oiling system addresses the need to properly lubricate an engine when it’s running. Properly lubricating an engine not only reduces friction between moving parts but is also the main method by which heat is removed from pistons, bearings, and shafts. Failing to properly lubricate an engine will result in engine failure. The oil pump forces the motor oil through the passages in the engine to properly distribute oil to different engine components. In a common oiling system, oil is drawn out of the oil sump (oil pan, in US English) through a wire mesh strainer that removes some of the larger pieces of debris from the oil. The flow made by the oil pump allows the oil to be distributed around the engine. In this system, oil flows through an oil filter and sometimes an oil cooler, before going through the engine’s oil passages and being dispersed to lubricate pistons, rings, springs, valve stems, and more.

Oil pressure

The oil pressure generated in most engines should be about 10 psi per every 1000 revolutions per minute (rpm), peaking around 55-65 psi.[2]

Local pressure (at the crankshaft journal and bearing) is far higher than the 50, 60 psi &c. set by the pump’s relief valve, and will reach hundreds of psi. This higher pressure is developed by the relative speeds in feet per second (not RPM or journal size directly) of the crankshaft journal itself against the bearing, the bearing width (to the closest pressure leak), oil viscosity, and temperature, balanced against the bearing clearance (the leakage rate).

All pump pressure does is “fill in the hole” and refresh the oil in the annular space faster than the leak expels it. This is why low-speed engines have relatively large journals, with only modest pump size and pressure. Low pressure indicates that leakage from the bearings is higher than the pump’s delivery rate.

Gauge pressure

The oil pressure at the pump outlet, which is what opens the pressure relief valve, is simply the resistance to flow caused by the bearing clearances and restrictions.

The oil pressure gauge, or warning lamp, gives only the pressure at the point where its sender enters that part of the pressurized system – not everywhere, not an average, nor a generalized picture of the systemic pressure.

Despite the frequent comparison to hydraulic engineering theory, this is not a “closed system” in which oil pressure is balanced and identical everywhere. All engines are “open systems”, because the oil returns to the pan by a series of controlled leaks. The bearings farthest from the pump always have the lowest pressure because of the number of leaks between the pump and that bearing. Excess bearing clearance increases the pressure loss between the first and last bearing in a series.

Depending on condition, an engine may have acceptable gauge pressure, and still only 5 psi pressure at one connecting rod, which will fail under high load.

The pressure is actually created by the resistance to the flow of the oil around the engine.[5] So, the pressure of the oil may vary during operation, with temperature, engine speed, and wear on the engine. Colder oil temperature can cause higher pressure, as the oil is thicker, while higher engine speeds cause the pump to run faster and push more oil through the engine. Because of variances in temperature and normal higher engine speed upon cold engine start up, it’s normal to see higher oil pressure upon engine start up than at normal operating temperatures, where normal oil pressure usually falls between 30 and 45 psi.[6] Too much oil pressure can create unnecessary work for the engine and even add air into the system. To ensure that the oil pressure does not exceed the rated maximum, once pressure exceeds a preset limit a spring-loaded pressure relief valve dumps excess pressure either to the suction side of the pump, or directly back to the oil pan or tank.

High oil pressure frequently means extremely high pressure on cold start-up, but this is a design flaw rather than an automatic consequence of high pressure. The observation “if you raise the maximum pressure, the cold pressure goes too high” is accurate, but not intentional.

Even the stock pumps (regardless of brand and model) do not have enough relief valve capacity: the relief port is too small to handle the volume of cold oil. This is why there is a significant difference between cold & hot oil, high & low RPM, &c., but it’s typically not a problem with stock engines. A correctly designed relief port (which is not found in production engines) will flow any oil volume the gears will pass, regardless of oil viscosity or temperature, and the gauge reading will only vary slightly.

The oil pressure is monitored by an oil pressure sending unit, usually mounted to the block of the engine. This can either be a spring-loaded pressure sensor or an electronic pressure sensor, depending on the type of sending unit. Problems with the oil pressure sending unit or the connections between it and the driver's display can cause abnormal oil pressure readings when oil pressure is perfectly acceptable.

Low Oil Pressure

Low oil pressure, however, can cause engine damage. Low oil pressure can be caused by many things, such as a faulty oil pump, a clogged oil pickup screen, excessive wear on high mileage engines, or simply low oil volume. Indications of low oil pressure may be that the warning light is on, a low pressure reading on the gauge, or clattering/clinking noises from the engine. Low oil pressure is a problem that must be addressed immediately to prevent serious damage.

The leading cause of low oil pressure in an engine is wear on the engine’s vital parts. Over time, engine bearings and seals suffer from wear and tear. Wear can cause these parts to eventually lose their original dimensions, and this increased clearance allows for a greater volume of oil to flow over time which can greatly reduce oil pressure. For instance, .001 of an inch worn off of the engine’s main bearings can cause up to a 20% loss in oil pressure.[5] Simply replacing worn bearings may fix this problem, but in older engines with a lot of wear not much can be done besides completely overhauling the engine which is generally not cost effective.

Particles in the oil can also cause serious problems with oil pressure. After oil flows through the engine, it returns to the oil pan, and can carry along a lot of debris. The debris can cause problems with the oil pickup screen and the oil pump itself. The holes in the oil pickup screen measure about 0.04 square inches (0.26 cm2).[5] Holes of this size only pick up bigger pieces of debris and allow a lot of smaller pieces to flow through it. The holes in the screen are so big (relative to debris) because at low temperatures and slow engine speed the oil is very viscous and needs large openings to flow freely. Even with these large holes in the screen, it can still become clogged and cause low oil pressure. A .005-inch-thick (0.13 mm) coating on the screen can reduce hole size to about .03 square inches (0.19 cm2), which in turn reduces the flow of oil by 44 percent.[5]

Even after passing through the oil pickup screen and the oil filter, debris can remain in the oil. It is very important to change the oil and oil filter to minimize the amount of debris flowing through your engine. This harmful debris along with normal engine wear in high mileage engines causes an increase in clearances between bearings and other moving parts.

Low oil pressure may be simply because there is not enough oil in the sump, due to burning oil (normally caused by piston ring wear or worn valve seals) or leakage. The piston rings serve to seal the combustion chamber, as well as remove oil from the internal walls of the cylinder. However, when they wear, their effectiveness drops, which leaves oil on the cylinder walls during combustion. In some engines, burning a small amount of oil is normal and shouldn’t necessarily cause any alarm, where as burning lots of oil is a sign that the engine might be in need of an overhaul.

Oil Pumps in High Performance Engines

Not all engines have the same oiling needs. High performance engines, for example, place higher stress on the lubricating system. In this case, the lubricating system must be especially robust to prevent engine damage.[2] Most engines in cars on the road today don’t run much past 5,000–6,000 rpm, but that isn’t always the case in performance engines, where engine speeds could reach up to 8000-9000 rpm. In engines like these, it is imperative that the oil circulates quickly enough, or air may become trapped in the oil. Also, to free up power, some engines in performance applications run lower weight oil, which requires less power to run the oil pump. Common oil weights in engines today are usually either 5w30 or 10w30 oil, where as performance engines might use 0w20 oil, which is less viscous.[7]

Wet and dry sump systems

Conventional wet sump engines have one oil pump. It is generally located inside the lower part of the engine, usually below and/or to one side of the crankshaft. On dry sump engines, at least two oil pumps are required: one to pressurize and distribute the oil around the engine components, and at least one other 'scavenge pump' to evacuate the oil which has pooled at the bottom of the engine.[8] This scavenge pump is sometimes (but not always) located in the 'sump' of the engine, and crucially, this scavenge pump's flow-rate capacity must exceed that of the pump which pressurizes and distributes oil throughout the engine.

Because of the dry sump's external oil reservoir, excess air can escape the oil before the oil is pumped back through the engine. Dry sumps also allow for more power because it reduces the amount of windage, oil sloshing up into the rotating assembly, and the vacuum from the scavenge pump improves ring seal.[9] Dry sumps are more popular in racing applications because of the improved power and reduced oil sloshing that would otherwise reduce oil pressure. Disadvantages of dry sumps are increased weight, additional parts, and more chances for leaks and problems to occur.

See also

  • Ring oiler

References

  1. ^ Sliding vane pumps have become less common, as modern manufacturing techniques can more cheaply produce the complex precise shapes needed for other pump types. As engine life becomes longer and more reliable, the wear aspect of the sliding vanes also becomes a concern.
  2. ^ For reasons of oil viscosity, a large slow pump requires less power to move the same oil volume as a small fast pump
  3. ^ An alternative system uses a pressurised hydraulic accumulator filled with oil, rather than a pump.

External links

Engine Failure


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать реферат

Look at other dictionaries:

  • Oil pressure (internal combustion engine) — Oil pressure is an important factor in the longevity of most internal combustion engines. With a forced lubrication system (invented by Frederick Lanchester), oil is picked up by an oil pump and forced through oil galleries (drillings) into the… …   Wikipedia

  • Internal combustion engine — The internal combustion engine is an engine in which the combustion of a fuel (normally a fossil fuel) occurs with an oxidizer (usually air) in a combustion chamber. In an internal combustion engine, the expansion of the high temperature and high …   Wikipedia

  • Oil pump — may refer to: A hydraulic pump, which pressurizes hydraulic fluid in a hydraulic system An oil pump (internal combustion engine), a part of the lubrication system that pressurizes motor oil for distribution around the engine A pump jack, often… …   Wikipedia

  • History of the internal combustion engine — Various scientists and engineers contributed to the development of internal combustion engines: [ Otto engines running at the Western Minnesota Steam Threshers Reunion (WMSTR), in Rollag, Minnesota. (2min 16sec, 320x240, 340kbps video)] *1206: Al …   Wikipedia

  • Component parts of internal combustion engines — Internal combustion engines come in a wide variety of types, but have certain family resemblances, and thus share many common types of components. Contents 1 Combustion chambers 2 Ignition system 2.1 Spark 2.2 Compression …   Wikipedia

  • Engine braking — is where the retarding forces within an engine are used to slow a vehicle down, as opposed to using an external braking mechanism, for example friction brakes or magnetic brakes. The term is often confused with several other types of braking,… …   Wikipedia

  • Engine knocking — Pinging redirects here. For other uses, see Ping (disambiguation). Knocking (also called knock, detonation, spark knock, pinging or pinking) in spark ignition internal combustion engines occurs when combustion of the air/fuel mixture in the… …   Wikipedia

  • Pump — For information on Wikipedia project related discussions, see . A pump is a device used to move gases, liquids or slurries. A pump moves liquids or gases from lower pressure to higher pressure, and overcomes this difference in pressure by adding… …   Wikipedia

  • Engine displacement — One complete cycle of a four cylinder, four stroke engine. The volume displaced is marked in orange. Engine displacement is the volume swept by all the pistons inside the cylinders of an internal combustion engine in a single movement from top… …   Wikipedia

  • Engine cooling — is cooling an engine, typically using either air or liquid.OverviewHeat engines generate mechanical power by extracting energy from heat flows, much as a water wheel extracts mechanical power from a flow of mass falling through a distance.… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”