Orbiter Boom Sensor System

Orbiter Boom Sensor System
Shuttle Remote Manipulator System (RMS) holding OBSS boom on STS-114
Astronaut Scott Parazynski at the end of the OBSS boom making repairs to the P6 solar array

The Orbiter Boom Sensor System (OBSS) is a 50-foot boom carried on board NASA's Space Shuttles. The boom can be grappled by the Canadarm and serves as an extension of the arm, doubling its length to a combined total of 100 feet (30 m).[1] At the far end of the boom is an instrumentation package of cameras and lasers used to scan the leading edges of the wings, the nose cap, and the crew compartment after each lift-off and before each landing. If flight engineers suspect potential damage to other areas, as evidenced in imagery captured during lift-off or the rendezvous pitch maneuver, then additional regions may be scanned.

The OBSS was introduced to the shuttle fleet with STS-114, the "Return to Flight" mission executed by Discovery, and was flown on every mission since. It is used to inspect the shuttle for damage to the heatshield, officially called Thermal Protection System (TPS), that could jeopardize the shuttle during re-entry. The decision to perform focused inspections of the TPS was prompted by the Space Shuttle Columbia disaster, in which a shuttle was destroyed due to damage inflicted to the heatshield during lift-off. The OBSS is central to focused inspections of the TPS, not only because it carries all the instruments necessary for detailed measurements and observations, but also because without it the Canadarm is too short to reach to all the areas that need to be surveyed.

Contents

Description

The boom is essentially the same design as the Canadarm itself, except that the articulatory joints are fixed.[2] OBSS arms for the three remaining orbiters were manufactured relatively quickly, primarily because some spare parts for the Canadarm system were used.

Two instrumentation packages are installed at the far end of the OBSS. Sensor package 1 consists of the Laser Dynamic Range Imager (LDRI) and an Intensified Television Camera (ITVC). Sensor package 2 is the Laser Camera System (LCS) and a digital camera (IDC). The sensors can record at a resolution of a few millimeters, and can scan at a rate of about 2.5 inches (64 mm) per second.

It is also fitted with handrails, so that the boom could be used to provide spacewalkers with access to the shuttle's underbelly in case in-flight repairs are required.

STS-120 ISS repair

During STS-120 the OBSS was used as an extension boom for the space station's Canadarm2, something it was never designed to do. During this mission the P6 solar array had become damaged during the redeploy. Canadarm2 grabbed the arm on its center grapple fixture and then astronaut Scott E. Parazynski was mounted at the end of the boom to make the repair. Because Canadarm2 is unable to power the OBSS it was without power many hours more than it was designed to handle, but because it was heated up considerably before the start of the repair it stayed undamaged.

Enhanced ISS Boom Assembly

Due to the benefits for spacewalkers from the extended range provided by connecting an OBSS to the International Space Station(ISS)'s robotic arm, NASA implemented a plan for the STS-134 Space Shuttle mission to leave its OBSS behind on the ISS, where it will permanently remain. [3] The plan resulted in a number of modifications to the OBSS, now known as the Enhanced ISS Boom Assembly, including the addition of a Power Data and Grapple Fixture which enables mating to the robotic arm on the end of the boom with a Canadarm2-compatible grapple fixture to favor station use. The boom was stowed on the ISS S1 Integrated Truss Structure on the fourth spacewalk of STS-134 on May 27, 2011. The OBSS sensors were disconnected during the EVA, and are not designed to withstand thermal conditions outside the ISS without power to keep them warm. However, the modification of the grapple fixture could enable such equipment to be mounted onto the OBSS in the future.[4]

References

External links


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать курсовую

Look at other dictionaries:

  • Orbiter Boom Sensor System — OBSS im Hangar …   Deutsch Wikipedia

  • Orbiter Boom Sensor System — El sistema manipulador remoto del transbordador (RMS) manteniendo la pluma OBSS durante la STS 114 …   Wikipedia Español

  • Orbiter Boom Sensor System — Le bras robotique portant la perche OBSS L Orbiter Boom Sensor System (ou perche OBSS) est une extension du bras robotique Canadarm de la navette spatiale américaine. Conçue après la perte de l orbiteur Columbia en 2003, elle sert à inspecter le… …   Wikipédia en Français

  • Orbital Boom Sensor System — Das OBSS im Hangar Das OBSS bei der Arbeit Das Orbiter Boom Sensor System (OBSS, dt. Orbiter Auslegersensorsystem) ist ein 15,33 Meter langer Ausleger mit einer Vielzahl von Instrumenten, der an das …   Deutsch Wikipedia

  • Orbiter Vehicle — Space Shuttle Die Atlantis startet zur Mission STS 115 Orbiter Länge 37,24 m Spannweite 23,79 m Startgewicht (maximal) 109.000 kg …   Deutsch Wikipedia

  • Shuttle Remote Manipulator System — Vue sur la baie de stockage de la navette spatiale avec à droite le Canadarm déployé Le Shuttle Remote Manipulator System (SRMS), ou Canadarm (nom qui évoque le fait qu il a été conçu au Canada), est un bras mécanique attaché à la navette… …   Wikipédia en Français

  • Space Transportation System — Space Shuttle Die Atlantis startet zur Mission STS 115 Orbiter Länge 37,24 m Spannweite 23,79 m Startgewicht (maximal) 109.000 kg …   Deutsch Wikipedia

  • Space Shuttle thermal protection system — The Space Shuttle thermal protection system (TPS) is the barrier that protects the Space Shuttle Orbiter during the searing 1650 °C (3000 °F) heat of atmospheric reentry. A secondary goal is to protect from the heat and cold of space while on… …   Wikipedia

  • Laser Camera System — Neptec Design Group s Laser Camera System (LCS) is short range, high precision autosynchronous triangulation scanner – or more simply, a very sensitive, highly accurate 3D scanner. Using a laser to measure the distance between itself and a… …   Wikipedia

  • Laser Camera System — Das Laser Camera System (LCS) ist ein Instrument, um 3 dimensionale Bilddaten des Space Shuttles im All zu erstellen. Es wurde im Auftrag der NASA von der kanadischen Firma Neptec entwickelt. Das System dient der Überprüfung des Hitzeschildes auf …   Deutsch Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”