- Compressed-air energy storage
Compressed Air Energy Storage (CAES) refers to the compression of airto be used later as energy source. At utility scale, it can be stored during periods of low energy demand (off-peak), for use in meeting periods of higher demand (
peak load ). Alternatively it can be used to power tools, or even vehicles. (see also:Pressure vessel )Types
Compressed air energy storage can be done
adiabatically ,diabatically , orisothermally :
* With Adiabatic storage, the heat that appears during compression is also stored, then returned to the air when the air is expanded. This is a subject of ongoing study, but no utility scale plants of this type have been built. The theoretical efficiency of adiabatic energy storage approaches 100% for large and/or rapidly cycled devices and/or perfect thermal insulation, but in practice round trip efficiency is expected to be 70%cite web|title=German AACAES project information | url=http://www.bine.info/pdf/publikation/projekt0507englinternetx.pdf | accessdate=2008-02-22] . Heat can be stored in a solid such as concrete or stone, or more likely in a fluid such as hot oil (up to 300C) or a molten-salt (600C).* With Diabatic storage, the extra heat is removed from the air with inter coolers following compression (thus approaching isothermal compression), and is dissipated into the atmosphere as waste. Upon removal from storage, the air must be re-heated (usually in a natural gas fired burner for utility grade storage or with a heated metal mass for large Uninterruptible Power Supplies) prior to expansion in the turbine to power a generator. The heat discarded in the intercoolers degrades efficiency, but the system is simpler than the adiabatic one, and thus far is the only system which has been implemented commercially. The McIntosh CAES plant requires 0.69kWh of electricity and 1.17kWh of gas for each 1.0kWh of electrical output (a non-CAES natural gas plant can be up to 60% efficient therefore uses 1.67kWh of gas per kWh generated).
* Isothermal compression and expansion (which attempts constant temperature operation by constant heat exchange to the environment) approaches is only practical for rather low power levels, unless very effective heat exchangers can be incorporated. The theoretical efficiency of isothermal energy storage approaches 100% for small and/or slowly cycled devices and/or perfect heat transfer to the environment.In practice neither of these perfect thermodynamic cycles are obtainable, as some heat losses are unavoidable.A highly efficient arrangement, which fits neatly into none of the above categories, uses high, medium and low pressure pistons in series, with each stage followed by an airblast venturi that draws ambient air (or seawater as in early compressed air torpedo [
Compressed air torpedo ] designs) over an air-to-air (or air-to-seawater)heat exchanger between each expansion stage. This warms the exhaust of the preceding stage and admits this preheated air to the following stage. This practice was widely practiced on various compressed air vehicles such asH. K. Porter, Inc in mining locomotives ( [ [http://www.dself.dsl.pipex.com/MUSEUM/TRANSPORT/comprair/comprair.htm Compressed-Air Propulsion ] ] see CHARLES HODGES AND THE PORTER COMPOUND AIR LOCOMOTIVES ) and trams. http://www.aircaraccess.com/images/3stage%201.jpg] .Here the heat of compression is effectively stored in the atmosphere (or sea) and returned later on, but interestingly it is not not the "same" heat.
Compression can be done with electrically powered
turbo-compressor s, expansion with turbo 'expanders' driving electrical generatorscite web
title=Distributed Energy Program: Compressed Air Energy Storage
url=http://www.eere.energy.gov/de/compressed_air.html
publisher=United States Department of Energyone
accessdate=2006-08-27] orair engine s (generator ) to produce electricity.Air is stored in mass quantity in underground in a cavern created by
solution mining (salt is dissolved away) [http://www.answers.com/topic/solution-mining?cat=technology ; http://www.saltinstitute.org/12.html ] or an abandoned mine. Plants are designed to operate on a daily cycle, charging at night and discharging during the day.Compressed air energy storage can also be used to describe technology on a smaller scale such as exploited by
air car s orwind farm s in steel orcarbon-fiber tanks.Physics of isothermal compressed air storage
One type of reversible air compression and expansion is described by the
isothermal process , where the heat of compression and expansion is removed or added to the system at the same rate as it is produced. Compressing air heats it up and the heat must therefore be able to flow to the environment during compression for the temperature to remain constant. In practice this is often not the case, because to properly intercool a compressor requires a compact internal heat exchanger that is optimized for highheat transfer and low pressure drop. Without an internal heat exchanger, isothermal compression can be approached at low flow rates, particularly for small systems. Small compressors have higher inherent heat exchange, due to a higher ratio of surface area to volume. Nevertheless it is useful to describe the limiting case of ideal isothermal compression of anideal gas :The
ideal gas law , for an isothermal process is:: By the definition of work, where A and B are the initial and final states of the system:::where, , and so,: is the absolute
pressure , : is thevolume of the vessel,: is theamount of substance of gas,: is theideal gas constant ,: is theabsolute temperature ,: is theenergy stored or released.This amounts to about 2.271 kJ at 0 degrees Celsius (273.15 kelvin) or 2.478 kJ at 25 °C (298 K), per mole.
One mole of gas molecules at
standard temperature and pressure (0 °C, 0.1 MPa), occupies 22.4 liters and there are 1000 liters in 1 m³. So there are about moles of gas molecules in 1 m³ and we get 101 kJ at 0 °C or 111 kJ at 25 °C per m³ of gas (at 0.1 MPa = aprox. atmospheric pressure):An isothermal process is thermodynamically reversible, so to the extent the processes are isothermal, the efficiency of compressed air storage will approach 100%. The equation above represents the maximum energy that can be stored. In practice, the process will not be perfectly isothermal and the compressors and motors will have heat-related energy losses.
When gas is compressed
adiabatic ally, some of the compression work goes into heating the gas. If this heat is then lost to the surroundings, and assuming the same quantity of heat is not added back to the gas upon expansion, the energy storage efficiency will be reduced. Energy storage systems often use large natural underground caverns. This is the preferred system design, due to the very large gas volume, and thus the large quantity of energy that can be stored with only a small change in pressure. The cavern space can be compressed adiabatically and the resulting temperature change and heat losses are small.Practical constraints in transportation
Energy density and efficiency
Compressing air heats it up and expanding it cools it down. Therefore practical air engines require heat exchangers in order to avoid excessively high or low temperatures and even so don't reach ideal constant temperature conditions. Nevertheless it is useful to describe the maximum energy storable using the isothermal case, which works out to about 110 kJ/m3-N at 24°Celsius. One m3-N is one cubic meter of gas volume at normal, i.e. atmospheric pressure, conditions. Thus if 1.0 m3 of ambient air is very slowly compressed into a 5-liter bottle at 200 bar, the potential energy stored is 583 kJ (or 0.16 kWh). A highly efficient air motor could transfer this into kinetic energy if it runs very slowly and manages to expand the air from its initial 200 bar pressure completely down to 1 bar (bottle completely "empty" at ambient pressure). Achieving high efficiency is a technical challenge both due to nonlinear energy storage and the thermodynamic considerations. If the bottle above is emptied down to 10 bar, the energy extractable is about 330 kJ at the motor shaft. The efficiency of isothermal compressed gas storage is theoretically 100% but in practice the process is not isothermal and the two engines (compressor and motor) have additional types of losses.
A standard 200 bar 5 liter steel bottle has a mass of 7.5 kg, a superior one, 5 kg. Bottles reinforced with, or built from, high-tensile fibers such as
carbon-fiber orkevlar can be below 2 kg in this size, consistent with the legal safety codes. 1 m3 of air contained inside such a full bottle has a mass of 1.225 kg (at 0°C). Thus, theoretical energy densities are from roughly 70 kJ/kg at the motor shaft for a plain steel bottle to 180 kJ/kg at the motor shaft for an advanced fiber-wound one, whereas practical achievable energy densities for the same containers would be from 40 kJ/kg to 100 kJ/kg. Comparing to the data given for rechargeable batteries, this makes the advanced fiber-reinforced bottle example comparable to thelead-acid battery in terms of energy density and advanced battery systems are several times better. Batteries also provide nearly constant voltage over their entire charge level, whereas the pressure of compressed air storage varies greatly with charge level. It is technically challenging to design air engines to maintain high efficiency and sufficient power over such a wide range of pressures. Compressed air can transfer power at very high rates, which is a principal objective of transportation prime-movers, for acceleration and deceleration; particularly forhybrid vehicles .Advantages of compressed air over electric storage are the longer lifetime of
pressure vessel s compared to batteries and the lower toxicity of the materials used. Costs are thus potentially lower, however advanced pressure vessels are costly to develop and safety-test and at present are more expensive than mass-produced batteries.As with electric technology, it must be stressed that compressed air energy storage depends on external energy sources and overall consumption can only be as "clean" as these.
afety
As with most technologies, compressed air has safety concerns, mainly the catastrophic rupture of the tank. Highly conservative safety codes make this a rare occurrence at the tradeoff of higher weight. Codes may limit the legal working pressure to less than 40% of the rupture pressure for steel bottles (
safety factor of 2.5), and less than 20% for fiber-wound bottles (safety factor of 5). Design rules are according to theISO 11439 standard. [ [http://www.iso.org/iso/catalogue_detail?csnumber=33298 Gas cylinders -- High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles] ] High pressure bottles are fairly strong so that they generally do not rupture in crashes.Compressed air vehicles
History
The air engine and its idea of using air as an energy carrier is not new. Air has been used since the 19th century to power mine
locomotives , and was at one time the basis of navaltorpedo propulsion.Compressed air is still currently used in
racecar s to provide the initial energy needed to start the car's main power plant, theinternal combustion engine (ICE).Many people have been working on the idea of compressed air vehicles with renewed interest since the 1990s
energy crisis .Engine
A compressed air engine uses the expansion of compressed air to drive the pistons of an engine, an axle, or to drive a turbine.
Sometimes efficiency is increased by the following methods:
* A turbine with continuous expansion at high efficiency
* several stages of expansion
* use of waste heat, notably in a hybridheat engine design
* use of environmental heatA highly efficient arrangement uses high, medium and low pressure pistons in series, with each stage followed by an airblast venturi that draws ambient air over an air-to-air
heat exchanger between each expansion stage. This warms the exhaust of the preceding stage and admits this preheated air to the following stage..The only exhaust gas from each stage is cold air which can be as cold as (−15 °C), this may also be used for
air conditioning in a car.Additional heat can be supplied by burning fuel as in 1904 for Whitehead's torpedoes [ [http://www.btinternet.com/~philipr/torps.htm A History of the Torpedo The Early Days ] ] . This improves the range and speed available for a given tank volume at the cost of the additional fuel.
As an alternative to pistons or turbines, the
Quasiturbine is also capable of running on compressed air, and is thus also a compressed air engine.Cars
Several companies claim to have been developing compressed air cars for public use, since about 1990, but none are available yet. Typically the main advantages are claimed to be: no roadside emissions, low cost technology, engine uses food oil for lubrication, and integrated air conditioning.
The tanks may be refilled at a service station (using volume transfer), or in a few hours at home or in
parking lot s plugging the car into the electricgrid via an on-boardcompressor . The cost of driving such car is typically projected to be around €0.75 per 100 km, with a complete refill at the "tank-station" at about US$3.Other uses
Besides the use of
compressed air engine s for propulsion, compressed air is used forpower generation and inpaintball .Many dentists and shop tools use small turbine expanders for power, and many larger tools used in high electrical shock risk environments are pneumatic driven instead of electrically powered.Types of systems
Hybrid systems
The system can be a hybrid power generation system, with the stored compressed air mixed with a fuel suitable for an
internal combustion engine . For example,natural gas orbiogas can be added, then combusted to heat the compressed air, and then expanded in a conventionalgas turbine engine (or the rear portion of ajet engine ), using theBrayton cycle .In addition,
Compressed air engine s can be used in conjunction with an electric battery. The compressed air engine, drawing its energy from compressed air tanks, recharge the electric battery. This system (called a Pne-PHEV or Pneumatic Plug-in Hybrid Electric Vehicle-system)Fact|date=April 2008 and was being promoted by the apparently defunctEnergine [ [http://www.energine.com/phev/e_phev_03.php Energine PHEV-system schematic] ] .Existing hybrid systems
A hybrid plant was commissioned in Huntorf (Germany) in 1978, and again in
McIntosh, Alabama in 1991 (USA). cite journal|title=Squeeze the breeze: Want to get more electricity from the wind? The key lies beneath our feet|journal=New Scientist|date=2007-11-17 |first=Daniel|last=Pendick |volume=195|issue=2623|pages=4 |url=http://environment.newscientist.com/channel/earth/mg19526231.700-rocks-could-be-novel-store-for-wind-energy.html|format=|accessdate=2007-11-17 ] Both systems use off-peak energy for the air compression. cite web|url=http://www.caes.net/mcintosh.html |title=McIntosh project |accessdate=2007-11-17 |work=CAES Development Company corporation website |publisher=CAES Development Company L.L.C. ]The operating duration of the McIntosh plant is 24 hours, with the extended operation being achieved through the combined burning of a natural gas/compressed air mix.
Future hybrid systems
A proposed hybrid power plant is under consideration in Iowa. The design calls for a 75 - 150 MW wind farm, where the wind power will be used for air compression. [ [http://www.isepa.com/FAQs.asp Frequently Asked Questions] ] Power output of the McIntosh and Iowa gas/compressed air generation systems is in the range of 2-300 MW.
Additional facilities are under development in
Norton, Ohio andIowa Stored Energy Park (ISEP). This 2700 MWNorton project has been started in 2001, but in early 2007 construction had not actually begun. [cite web
title=Staff investigation report and recommendation
url=http://dis.puc.state.oh.us/DISOCR.nsf/0/49C28286DB6EE5388525712C0046945B/$FILE/DIGK2XU4ZGJWTKO%23.txt
publisher=Electric Power Generating Facility in Norton
date=2006-08-03
accessdate=2006-08-27]Increased efficiency is expected at ISEP, due to the use of
aquifer storage rather than cavern storage. The displacement of water in the aquifer results in regulation of the air pressure by the constant hydrostatic pressure of the water. A spokesperson for ISEP claims "you can optimize your equipment for better efficiency if you have a constant pressure." cite journal|title=Squeeze the breeze: Want to get more electricity from the wind? The key lies beneath our feet|journal=New Scientist|date=2007-11-17 |first=Daniel|last=Pendick |volume=195|issue=2623|pages=4 |url=http://environment.newscientist.com/channel/earth/mg19526231.700-rocks-could-be-novel-store-for-wind-energy.html|format=|accessdate=2007-11-17 ] It is planned to have 75 - 150 MW of capacity. cite web|url=http://www.isepa.com/about_isep.asp |title=About the Iowa Stored Energy Park |accessdate=2007-11-17 |work=ISEPA corporate web site |publisher=Iowa Stored Energy Plant Agency ]Lake or ocean storage
Wikimedia Foundation. 2010.