Ti-sapphire laser

Ti-sapphire laser

Ti:sapphire lasers (also known as Ti:Al2O3 lasers, titanium-sapphire lasers, or simply Ti:sapphs) are tunable lasers which emit red and near-infrared light in the range from 650 to 1100 nanometers. These lasers are mainly used in scientific research because of their tunability and their ability to generate ultrashort pulses. Lasers based on Ti:sapphire were first constructed in 1982. [P. F. Moulton, [http://josab.osa.org/abstract.cfm?id=3945 Spectroscopic and laser characteristics of Ti:Al2O3] , J. Opt. Soc. B, vol. 3, p. 125 (1986)] .

Titanium-sapphire refers to the lasing medium, a crystal of sapphire (Al2O3) that is doped with titanium ions. A Ti:sapphire laser is usually pumped with another laser with a wavelength of 514 to 532 nm, for which argon-ion lasers (514.5 nm) and frequency-doubled , , and lasers (527-532 nm) are used. Ti:sapphire lasers operate most efficiently at wavelengths near 800 nm.

Types of Ti:sapphire lasers

Mode-locked oscillators

Mode-locked oscillators generate ultrashort pulses with a typical duration between 10 femtoseconds and a few picoseconds, in special cases even around 5 femtoseconds. The pulse repetition frequency is in most cases around 70 to 90 MHz. Ti:sapphire oscillators are normally pumped with a continuous-wave laser beam from an argon or frequency-doubled laser. Typically, such an oscillator has an average output power of 0.5 to 1.5 watt.

Chirped-pulse amplifiers

These devices generate ultrashort, ultra-high-intensity pulses with a duration of 20 to 100 femtoseconds. A typical one stage amplifier can produce pulses of up to 5 millijoules in energy at a repetition frequency of 1000 hertz, while a larger, multistage facility can produce pulses up to several joules, with a repetition rate of up to 10 Hz. Usually, amplifiers crystals are pumped with a pulsed frequency-doubled laser at 527 nm and operate at 800 nm. Two different designs exist for the amplifier: regenerative amplifier and multi-pass amplifier.

Regenerative amplifiers operate by amplifying single pulses from an oscillator (see above). Instead of a normal cavity with a partially reflective mirror, they contain high-speed optical switches that insert a pulse into a cavity and take the pulse out of the cavity exactly at the right moment when it has been amplified to a high intensity. The term 'chirped-pulse' refers to a special construction that is necessary to prevent the pulse from damaging the components in the laser.

In a multi-pass amplifier, there are no optical switches. Instead, mirrors guide the beam a fixed number of times (two or more) through the Ti:sapphire crystal with slightly different directions. A pulsed pump beam can also be multi-passed through the crystal, so that more and more passes pump the crystal. First the pump beam pumps a spot in the gain medium. Then the signal beam first passes through the center for maximal amplification, but in later passes the diameter is increased to stay below the damage-threshold, to avoid amplification the outer parts of the beam, thus increasing beam quality and cutting off some amplified spontaneous emission and to completely deplete the inversion in the gain medium.

The pulses from chirped-pulse amplifiers are often converted to other wavelengths by means of various nonlinear optics processes.

At 5 mJ in 100 femtoseconds, the peak power of such a laser is 50 gigawatts, which is many times more than what a large electrical power plant delivers (about 1 GW). When focused by a lens, these laser pulses will destroy any material placed in the focus, including air molecules.

Tunable continuous wave lasers

Titanium-sapphire is especially suitable for pulsed lasers since an ultrashort pulse inherently contains a wide spectrum of frequency components. This is an inherent property of the Fourier transform. However, with an appropriate design, titanium-sapphire can also be used in continuous wave lasers with extremely narrow linewidths tunable over a wide range.

Application to generation of pulsed hard radiation

When a laser pulse passes an electron the electron is shaken heavily, but afterwards it flies on as if nothing has happened, though a little bit of Compton scattering has taken place. Additionally an electron can either enter or leave an atom and in this processthe electron can either emit a X-ray photon or absorb a X-ray photon. In a complex situation with an atom, an electron, and a laser pulse, either the energy of the X-ray photon depends on the electric field of the laser pulse at the time of creation or the energy of the electron depends on the electric field of the laser pulse at the time of leaving the atom. This is called either pulsed X-ray generation or attosecond transient recorder. Though the atom and the laser pulse interact in various ways, this is ignored here (see high harmonics generation instead).

References

External links

* [http://www.rp-photonics.com/titanium_sapphire_lasers.html Encyclopedia of laser physics and technology on Ti:sapphire lasers]


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать реферат

Look at other dictionaries:

  • laser-annealed silicon-on-sapphire — lazeriu atkaitintas silicio darinys ant safyro statusas T sritis radioelektronika atitikmenys: angl. laser annealed silicon on sapphire; laser annealed silicon on sapphire structure vok. laserausgeheilte Silizium auf Saphir Struktur, f rus. КНС… …   Radioelektronikos terminų žodynas

  • laser-annealed silicon-on-sapphire structure — lazeriu atkaitintas silicio darinys ant safyro statusas T sritis radioelektronika atitikmenys: angl. laser annealed silicon on sapphire; laser annealed silicon on sapphire structure vok. laserausgeheilte Silizium auf Saphir Struktur, f rus. КНС… …   Radioelektronikos terminų žodynas

  • Laser — For other uses, see Laser (disambiguation). United States Air Force laser experiment …   Wikipedia

  • Sapphire — For other uses, see Sapphire (disambiguation). Sapphire The 423 carat (85 g) blue Logan sapphire General Category Oxide mineral …   Wikipedia

  • Laser construction — A laser is constructed from three principal parts:*An energy source (usually referred to as the pump or pump source ), *A gain medium or laser medium , and *Two or more mirrors that form an optical resonator . Pump sourceThe pump source is the… …   Wikipedia

  • laser — /lay zeuhr/, n. Physics. a device that produces a nearly parallel, nearly monochromatic, and coherent beam of light by exciting atoms to a higher energy level and causing them to radiate their energy in phase. Also called optical maser. [1955 60; …   Universalium

  • Laser turntable — A laser turntable is a phonograph that plays gramophone records using a laser beam as the pickup, rather than a conventional diamond tipped stylus. This playback system has the unique mechanical advantage of never physically touching the record… …   Wikipedia

  • Laser femtoseconde — Un laser femtoseconde est un type de laser particulier qui produit des impulsions ultra courtes dont la durée est de l ordre de quelques femtosecondes à quelques centaines de femtosecondes (1 fs = 1 femtoseconde = 10 15 secondes). Ce type de… …   Wikipédia en Français

  • laser- — la|ser «LAY zuhr», noun, verb. –n. 1. a device that produces a very narrow and intense beam of light of only one wavelength going in only one direction; optical maser. Laser beams are used to cut or melt hard materials, remove diseased body… …   Useful english dictionary

  • Différents types de laser — Liste des différents types de laser Ceci est une liste des différents types de lasers avec la longueur d onde sur laquelle ils opèrent et leurs applications. Il existe plusieurs milliers de sortes de lasers mais la plupart d entre eux ne sont… …   Wikipédia en Français

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”