Southern valve gear

Southern valve gear

Southern valve gear was briefly popular on steam locomotives in the United States. It combines elements of the Walschaerts and Baker patterns.

History

Southern valve gear was devised by locomotive designers on the Southern Railway (US) and used on many locomotives on that line. The first patent was issued to Wm. Sherman Brown in 1906. He continued work and another patent was issued July 23, 1912. The gear was first tested on Mikado 586 in February, 1913 at Southern Knoxville Shops. It was specified for some USRA standard locomotive designs, though many locomotives constructed to these patterns used Walschaerts or Baker valve gear instead. The Southern valve gear was used on Pennsylvania Railroad Class N2s as delivered. It was also used on East Broad Top numbers 16-18, which survive today.

Operation

Unlike the Walschaerts and Baker systems, the Southern valve gear dispensed with the combination lever which transmitted some of the crosshead motion to the valves. As with those systems it used a return crank on a driver (instead of the eccentrics used by the Stephenson valve gear). The return crank attached to the eccentric rod, which hung from a pivot close to the far end of the eccentric rod. This pivot attached to the end of the radius hanger, the other end of which attached to a link block which slid back and forth in a track curved in the same manner as the expansion link of a Walschaerts gear. In this system, however, the track was fixed in place; sliding the link block back and forth controlled reversing and cutoff.

At the end of the eccentric rod, close to the radius hanger, the rod connected to the transmission yoke. The upper end of this rod connected to a bellcrank, which translated the up and down motion of the transmission yoke into back and forth motion of the valves.

The mechanism is a little less obvious than that of the other types, but control is fundamentally like that of the Baker system. In this case the controlling factor is the angle between the radius hanger and the transmission yoke; when they are parallel, there is little up-down motion of the transmission yoke and the engine is centered. As link block moves back and forth, the angle of the radius hanger changes, and the up and down motion of the transmission yoke in response to the back and forth motion of the eccentric rod is increased or decreased.

References

* [http://www.gutenberg.org/files/17783/17783-h/17783-h.htm The Traveling Engineers’ Association: Examination Questions and Answers] from [http://www.gutenberg.org/ Project Gutenberg]

External links

* [http://oak.cats.ohiou.edu/~gu292901/images/ebt17sideclose.jpgSouthern valve gear on EBT #17] excellent picture from [http://oak.cats.ohiou.edu/~gu292901/index.html Greg Udolph]


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать реферат

Look at other dictionaries:

  • Valve gear — The valve gear of a steam engine is the mechanism that operates the inlet and exhaust valves to admit steam into the cylinder and allow exhaust steam to escape, respectively, at the correct points in the cycle. It is sometimes referred to as the… …   Wikipedia

  • Baker valve gear — was the main competitor to Walschaerts valve gear for steam locomotives in the United States. Strictly speaking it was not a valve gear but a variable expansion mechanism adapted to the Walschaerts layout replacing the expansion link and sliding… …   Wikipedia

  • Bulleid chain-driven valve gear — and were based upon motor vehicle practice in an attempt to create a compact, but efficient design with a minimum of service requirements. Design principles Oliver Bulleid s decision to have three cylinders, all driving the middle coupled axle of …   Wikipedia

  • Gresley conjugated valve gear — The Gresley conjugated valve gear was a valve gear for steam locomotives designed by Sir Nigel Gresley, chief mechanical engineer of the LNER, assisted by Harold Holcroft. It enables a three cylinder locomotive to operate with only the two sets… …   Wikipedia

  • Southern Railway 4501 — Southern Railway #4501 on display in 2006 Power type Steam Builder Baldwin Locomotive Works Serial number 37085 Build date …   Wikipedia

  • Southern Railway (Great Britain) — The Southern Railway (SR), was a British railway company established in the 1923 Grouping. It contained notable examples of civil engineering, linking London with the Channel ports, South West England and Kent. The railway was formed by the… …   Wikipedia

  • Southern Arizona Transportation Museum — The Southern Arizona Transportation Museum is a railroad museum in Tucson, Arizona.The museum does not charge for admission. Guided tours of the facility are available for a small fee, by appointment only. The museum offers community events,… …   Wikipedia

  • New South Wales D55 class locomotive — New South Wales D55 class 5616 stands at Junee ready to depart with a train of wheat hopper wagons. Power type Steam Builder Clyde Engineering Build date 1918–1925 …   Wikipedia

  • Ravenglass and Eskdale Railway locomotives — River Mite at Dalegarth This article gives details of the locomotives used on the Ravenglass and Eskdale Railway, a 15 inches (380 mm) narrow gauge preserved railway line running for 7 miles (11 km) from Ravenglass on the Cumbrian coast …   Wikipedia

  • SR Merchant Navy class — SR Merchant Navy class[1] Official Southern Railway photograph of 21C1 Channe …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”