Overall pressure ratio

Overall pressure ratio

In aeronautical engineering, the term overall pressure ratio is defined as the ratio of the stagnation pressure as measured at the front and rear of the compressor of a gas turbine engine. Generally speaking, a higher overall pressure ratio implies higher efficiency, but the engine will weigh more, so there is a compromise.

Contents

History of overall pressure ratios

Early jet engines had limited pressure ratios due to construction innaccuracies of the compressors and various material limits. For instance, the Junkers Jumo 004 from World War II had an overall pressure ratio 3.14:1. The immediate post-war SNECMA Atar improved this marginally to 5.2:1. Improvements in materials, compressor blades, and especially the introduction of multi-spool engines with several different rotational speeds, led to the much higher pressure ratios common today. Modern civilian engines generally operate between 30 and 40:1. The three-spool Rolls-Royce Trent 900 used on the Airbus A380, for instance, has a pressure ratio of about 39:1.

Advantages of high overall pressure ratios

A high overall pressure ratio permits a larger area ratio nozzle to be fitted on the jet engine. This means that more of the heat energy is converted to jet speed, and energetic efficiency improves. This is reflected in improvements in the engine's specific fuel consumption.

Disadvantages of high overall pressure ratios

One of the primary limiting factors on pressure ratio in modern designs is that the air heats up as it is compressed. As the air travels through the compressor stages it can reach temperatures that pose a material failure risk for the compressor blades. This is especially true for the last compressor stage, and the inlet temperature to this stage, T_3\ , is a common figure of merit for engine designs. For civilian engines, the pressure ratio can be adjusted as the aircraft climbs, allowing it to offset some of the heat load through the lowered pressure and temperature of the high-altitude air. This is one of the many reasons airliners climb to high altitude as quickly as possible.

Military engines are often forced to work under conditions that maximize the heating load. For instance, the General Dynamics F-111 was required to operate at speeds of Mach 1.1 at sea level. As a side-effect of these wide operating conditions, and generally older technology in most cases, military engines typically have lower overall pressure ratios. The Pratt & Whitney TF30 used on the F-111 had a pressure ratio of about 20:1, while newer engines like the General Electric F110 and Pratt & Whitney F135 have improved this to about 30:1.

An additional issue is weight: a higher compression ratio implies a heavier engine, which in turn costs fuel to carry around. Thus, for a particular construction technology and set of flight plans an optimal overall pressure ratio can be determined.

Examples

Engine Overall pressure ratio notes
General Electric CF6 30.5:1 Boeing 747, A300
General Electric F110 30:1 F-14, F-15, F-16
Pratt & Whitney TF30 20:1 F-111
Rolls-Royce/Snecma Olympus 593 15.5:1 Concorde, Mach 2 engine

The Concorde's Olympus engines get additional compression from its supersonic inlet, yielding an effective overall pressure ratio of 80:1.[1]

Differences from other similar terms

The term should not be confused with the more familiar term compression ratio applied to reciprocating engines. Compression ratio is a ratio of volumes. In the case of the reciprocating engine, the maximum expansion of the charge is limited by the mechanical movement of the pistons (or rotor), and so the compression can be measured by simply comparing the volume of the cylinder with the piston at the top and bottom of its motion. The same is not true of the "open ended" gas turbine, where operational and structural issues are the limiting factors. Nevertheless the two terms are similar in that they both offer a quick way of determining overall efficiency relative to other engines of the same class.

The broadly equivalent measure of rocket engine efficiency is chamber pressure/exit pressure, and this ratio can be over 2000 for the Space Shuttle Main Engine.

Compression ratio versus overall pressure ratio

For any given gas mix compression ratio and overall pressure ratio are interrelated as follows:

CR 1:1 3:1 5:1 10:1 15:1 20:1 25:1 35:1
PR 1:1 4:1 10:1 22:1 40:1 56:1 75:1 110:1

The reason for this difference is that compression ratio is defined via the volume reduction,

CR=\frac{V_1}{V_2},

Pressure ratio is defined as the pressure increase

PR=\frac{P_2}{P_1}.

From the combined gas law we get:

\frac{P_1V_1}{T_1} = \frac{P_2V_2}{T_2} \Rightarrow
\frac{V_1}{V_2}=\frac{T_1}{T_2} \frac{P_2}{P_1} \Leftrightarrow
CR=\frac{T_1}{T_2} PR

Since T2 is much higher than T1 (compressing gases puts work into them, i.e. heats them up), CR is much lower than PR.

See also

References

  1. ^ Concorde: story of a supersonic pioneer By Kenneth Owen

Wikimedia Foundation. 2010.

Игры ⚽ Нужен реферат?

Look at other dictionaries:

  • Overall (disambiguation) — Overall may be used in the following circumstances Overall (garment) Overall (surname) comprehensive, all embracing Overall length Length overall, where overall is sometimes abbreviated as o/a, o.a. or oa Overall pressure ratio for the term… …   Wikipedia

  • Compression ratio — For compression ratio in data compression, see data compression ratio. The compression ratio of an internal combustion engine or external combustion engine is a value that represents the ratio of the volume of its combustion chamber from its… …   Wikipedia

  • Pressure vessel — Vertical pressure vessels installed in a structure A pressure vessel is a closed container designed to hold gases or liquids at a pressure substantially different from the ambient pressure. The pressure differential is dangerous and many fatal… …   Wikipedia

  • Stroke ratio — In a reciprocating piston engine, the stroke ratio, defined by either bore/stroke ratio or stroke/bore ratio, is a term which is used to describe the ratio between the diameter of the cylinder bore and the length of the piston stroke within its… …   Wikipedia

  • Partial pressure — In a mixture of ideal gases, each gas has a partial pressure which is the pressure which the gas would have if it alone occupied the volume.[1] The total pressure of a gas mixture is the sum of the partial pressures of each individual gas in the… …   Wikipedia

  • Lateral earth pressure — is the pressure that soil exerts in the horizontal plane. The common applications of lateral earth pressure theory are for the design of ground engineering structures such as retaining walls, basements, tunnels, and to determine the friction on… …   Wikipedia

  • Turbofan — [ CFM56 3 turbofan, lower half, side view.] A turbofan is a type of jet engine, similar to a turbojet. It essentially consists of a ducted fan with a smaller diameter turbojet engine mounted behind it that powers the fan. Part of the airstream… …   Wikipedia

  • Jet engine performance — This article describes how jet engine performance is estimated during the design phase. Similar techniques are used once the engine has been built and is being tested, except the performance of individual components, rather than being assumed, is …   Wikipedia

  • Components of jet engines — Diagram of a typical gas turbine jet engine. Air is compressed by the fan blades as it enters the engine, and it is mixed and burned with fuel in the combustion section. The hot exhaust gases provide forward thrust and turn the turbines which… …   Wikipedia

  • CFM International CFM56 — CFM56 …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”