Digital Audio Tape

Digital Audio Tape
Digital Audio Tape
DAT logo.svg
Dat cartridge.jpg
A 90-minute DAT cartridge, size compared to a AAA (LR03) battery.
Media type Magnetic tape
Capacity 120 minutes
Read mechanism Rotating head
Write mechanism Rotating head, helical scan
Developed by Sony
Usage Audio storage

Digital Audio Tape (DAT or R-DAT) is a signal recording and playback medium developed by Sony and introduced in 1987.[1] In appearance it is similar to a compact audio cassette, using 4 mm magnetic tape enclosed in a protective shell, but is roughly half the size at 73 mm × 54 mm × 10.5 mm. As the name suggests, the recording is digital rather than analog. DAT has the ability to record at higher, equal or lower sampling rates than a CD (48, 44.1 or 32 kHz sampling rate respectively) at 16 bits quantization. If a digital source is copied then the DAT will produce an exact clone, unlike other digital media such as Digital Compact Cassette or non-Hi-MD MiniDisc, both of which use a lossy data reduction system.

Like most formats of videocassette, a DAT cassette may only be recorded and played in one direction, unlike an analog compact audio cassette.

Although intended as a replacement for audio cassettes, the format was never widely adopted by consumers because of issues of expense and concerns about unauthorized digital quality copies. The format saw moderate success in professional markets and as a computer storage medium. As Sony has ceased production of new recorders, it will become more difficult to play archived recordings in this format unless they are copied to other formats or hard drives.

Contents

History

Development

The technology of DAT is closely based on that of video recorders, using a rotating head and helical scan to record data. This prevents DATs from being physically edited in the cut-and-splice manner of analog tapes, or open-reel digital tapes like ProDigi or DASH.

The DAT standard allows for four sampling modes: 32 kHz at 12 bits, and 32 kHz, 44.1 kHz or 48 kHz at 16 bits. Certain recorders operate outside the specification, allowing recording at 96 kHz and 24 bits (HHS). Some machines aimed at the domestic[where?] market did not operate at 44.1 kHz when recording from analog sources. Since each recording standard uses the same tape, the quality of the sampling has a direct relation to the duration of the recording – 32 kHz at 12 bits will allow six hours of recording onto a three hour tape while HHS will only give 90 minutes from the same tape. Included in the signal data are subcodes to indicate the start and end of tracks or to skip a section entirely; this allows for indexing and fast seeking. Two-channel stereo recording is supported under all sampling rates and bit depths, but the R-DAT standard does support 4-channel recording at 32 kHz.

DAT "tapes" are between 15 and 180 minutes in length, a 120-minute tape being 60 meters in length. DAT "tapes" longer than 60 meters tend to be problematic in DAT recorders due to the thinner media. DAT machines running at 48 kHz and 44.1 kHz sample rates transport the tape at 8.15 mm/s. DAT machines running at 32 kHz sample rate transport the tape at 4.075 mm/s.

Predecessor formats

DAT was not the first digital audio tape; pulse-code modulation (PCM) was used in Japan by Denon in 1972 for the mastering and production of analogue phonograph records, using a 2-inch Quadruplex-format videotape recorder for its transport, but this was not developed into a consumer product. Denon's development dated from its work with Japan's NHK Broadcasting; NHK developed the first high-fidelity PCM audio recorder in the late 1960s. Denon continued development of their PCM recorders that used professional video machines as the storage medium, eventually building 8-track units used for, among other productions, a series of jazz records made in New York in the late 1970s.

In 1976, another digital audio tape format was developed by Soundstream, using 1 inch (25.4 mm) wide reel-to-reel tape loaded on an instrumentation recorder manufactured by Honeywell acting as a transport, which in turn was connected to outboard digital audio encoding and decoding hardware of Soundstream's own design. Soundstream's format was improved through several prototypes and when it was developed to 50khz sampling rate at 16 bits, it was deemed good enough for professional classical recording by the company's first client, Telarc Records of Cleveland, Ohio. Telarc's April, 1978 recording of the Holst Suites for Band by Fred Fennell and the Cleveland Wind Ensemble was a landmark release, and ushered in digital recording for America's classical music labels. Soundstream's system was also used by RCA.

Starting in 1978, 3M introduced its own line and format of digital audio tape recorders for use in a recording studio. One of the first prototypes of 3M's system was installed in the studios of Sound 80 in Minneapolis, Minnesota. This system was used in June 1978 to record Aaron Copland's "Appalachian Spring" by the St. Paul Chamber Orchestra conducted by Dennis Russell Davies. That record was the first Grammy-winning digital recording. The production version of the 3M Digital Mastering System was used in 1979 to record the first all-digital rock album, Ry Cooder's "Bop Till You Drop," made at Warner Brothers Studio in California.

The first consumer-oriented PCM format used consumer video tape formats (Beta and VHS) as the storage medium. These systems used the EIAJ digital format, which sampled at 44.056khz at 14 bits. The Sony PCM-F1 system debuted in 1981, and Sony from the start offered the option of 16-bit wordlength. Other systems were marketed by Akai, JVC, Nakamichi and others. Panasonic, via its Technics division, briefly sold a digital recorder that combined a EIAJ digital adapter with a VHS video transport, the SV-P100. These machines were marketed by consumer electronics companies to consumers, but they were very pricey compared to cassette or even reel-to-reel decks of the time. They did catch on with the more budget conscious professional recordists, and some boutique-label professional releases were recorded using these machines.[2]

Starting in the early 1980s, professional systems using a PCM adaptor were also common as mastering formats. These systems digitized an analog audio signal and then encoded the resulting digital stream into an analog video signal so that a conventional VCR could be used as a storage medium.

One of the most significant examples of a PCM adaptor-based system was the Sony PCM-1600 digital audio mastering system, introduced in 1978. The PCM-1600 used a U-Matic-format VCR for its transport, connected to external digital audio processing hardware. It (and its later versions such as the PCM-1610 and 1630) was widely used for the production and mastering of some of the first Digital Audio CDs in the early 1980s. Once CD's were commercially introduced in 1983, tapes recorded on the PCM-1600 were sent to the CD pressing plants to be used to make the glass master disc for CD replication.

Other examples include dbx, Inc.'s Model 700 system, which, similar to modern Super Audio CDs, used a high sample-rate delta-sigma modulation rather than PCM; Decca's 1970s PCM system,[3] which used a videotape recorder manufactured by IVC for a transport; and Mitsubishi's X-80 digital recorder, a 6.4 mm (¼ in) open reel digital mastering format that used a very unusual sampling rate of 50.4 kHz.

For high-quality studio recording, all of these formats were effectively made obsolete in the early 1980s by two competing reel-to-reel formats with stationary heads: Sony's DASH format and Mitsubishi's continuation of the X-80 recorder, which was improved upon to become the ProDigi format. (In fact, one of the first ProDigi-format recorders, the Mitsubishi X-86C, was playback-compatible with tapes recorded on an X-80.) Both of these formats remained popular as an analog alternative until the early 1990s, when hard disk recorders rendered them obsolete.

R-DAT and S-DAT (DCC)

The DAT recorder mechanism was considerably more complex and expensive than an analogue cassette deck mechanism due to the rotary helical scan head, therefore Philips & Panasonic Corporation developed a rival digital tape recorder system with a stationary head based on the analogue compact cassette. The DCC was cheaper and simpler mechanically than DAT, but did not make perfect digital copies as it used a lossy compression technique called PASC. (Lossy compression was necessary to reduce the data rate to a level that a stationary head could cope with). DCC was never a competitor to DAT in recording studios because DAT was already established and as it was launched at the same time as Sony's Minidisc format (which has random access and editing features) it was not successful with consumers either. However, DCC proved that high quality digital recording could be achieved with a cheap simple mechanism using stationary heads.

Anti-DAT lobbying

In the late 1980s, the Recording Industry Association of America (RIAA) unsuccessfully lobbied against the introduction of DAT devices into the U.S. Initially, the organization threatened legal action against any manufacturer attempting to sell DAT machines in the country. It later sought to impose restrictions on DAT recorders to prevent them from being used to copy LPs, CDs, and prerecorded cassettes. One of these efforts, the Digital Audio Recorder Copycode Act of 1987 (introduced by Sen. Al Gore and Rep. Waxman), instigated by CBS Records president Walter Yetnikoff, involved a technology called CopyCode and required DAT machines to include a chip to detect attempts to copy material recorded with a notch filter,[clarification needed] meaning that copyrighted prerecorded music, whether analog or digital, would have distorted sound. A National Bureau of Standards study showed that not only were the effects plainly audible, but that it was not even effective at preventing copying.

This opposition by CBS softened after Sony, a DAT manufacturer, bought CBS Records in January 1988. By June 1989, an agreement was reached, and the only concession the RIAA would receive was a more practical recommendation from manufacturers to Congress that legislation be enacted to require that recorders have a Serial Copy Management System to prevent digital copying for more than a single generation.[4] This requirement was enacted as part of the Audio Home Recording Act of 1992, which also imposed taxes on DAT recorders and blank media.

Uses of DAT

Professional recording industry

DAT was used professionally in the 1990s by the professional audio recording industry as part of an emerging all-digital production chain also including digital multi-track recorders and digital mixing consoles that was used to create a fully digital recording. In this configuration, it is possible for the audio to remain digital from the first AD converter after the mic preamp until it is in a CD player.

Amateur and home use

DAT was envisaged by proponents as the successor format to analogue audio cassettes in the way that the compact disc was the successor to vinyl-based recordings; however, the technology was never as commercially popular as CD or cassette. DAT recorders remained relatively expensive, and commercial recordings were generally not made available on the format. However, DAT was, for a time, popular for making and trading recordings of live music (see bootleg recording), since available DAT recorders predated affordable CD recorders.

Computer data storage medium

The format was designed for audio use, but through the ISO Digital Data Storage standard was adopted for general data storage, storing from 1.3 to 80 GB on a 60 to 180 meter tape depending on the standard and compression. It is a sequential-access medium and is commonly used for backups. Due to the higher requirements for capacity and integrity in data backups, a computer-grade DAT was introduced, called DDS (Digital Data Storage). Although functionally similar to audio DATs, only a few DDS and DAT drives (in particular, those manufactured by Archive for SGI workstations)[5] are capable of reading the audio data from a DAT cassette. SGI DDS4 drives no longer have audio support; SGI removed the feature due to "lack of demand".[6]

Future of DAT

In November 2005, Sony announced that its remaining DAT machine models would be discontinued the following month.[7] Sony has sold around 660,000 DAT products since its introduction in 1987.[citation needed] However, the DAT format still finds regular use in film and television recording,[citation needed] principally due to the support in some recorders for SMPTE time code synchronization. It is slowly being superseded by modern hard disk recording equipment which offers much more flexibility and storage. In 2004, Sony introduced the Hi-MD Walkman with the ability to record in linear PCM. Hi-MD has found some favor as a disc-based DAT alternative for field recordings and general portable playback.[citation needed]

See also

References

  1. ^ Sony history Retrieved 19 September 2009
  2. ^ http://mixonline.com/TECnology-Hall-of-Fame/1981-sony-pcmf1/
  3. ^ G.Mancini (March 2004). "The Decca Digital Audio Recording System". http://www.mancini99.freeserve.co.uk/Decca_1.html. Retrieved 2007-10-25. 
  4. ^ Goldberg, Michael (1989-09-21). "Labels Back Down on DAT". Rolling Stone (561): 26. 
  5. ^ "Can you Rip DAT audio? (Ask Slashdot forum thread)". Slashdot. 1999-10-01. http://ask.slashdot.org/article.pl?sid=99/09/29/0451243. Retrieved 2007-10-25. 
  6. ^ "DAT/DDS hardware". 2003-03-26. Archived from the original on 2007-10-16. http://web.archive.org/web/20071016202400/http://homepage.ntlworld.com/adrian.rixon/personal/ade/dat-dds/drives.html. Retrieved 2007-10-25. 
  7. ^ "Sony Drops DAT". Anime News Service. Nov 15, 2005. http://www.animenewsservice.com/archives/nov30.htm. 

Wikimedia Foundation. 2010.

Игры ⚽ Нужен реферат?

Look at other dictionaries:

  • digital audio tape — n. an audio cassette tape recorded using digital techniques, resulting in sound that is virtually free of distortion * * * …   Universalium

  • digital audio tape — n. an audio cassette tape recorded using digital techniques, resulting in sound that is virtually free of distortion …   English World dictionary

  • Digital Audio Tape — Digital Audio Tape,   DAT …   Universal-Lexikon

  • Digital Audio Tape — У этого термина существуют и другие значения, см. DAT. DAT …   Википедия

  • Digital Audio Tape — Pour les articles homonymes, voir DAT. Une cassette DAT La Digital Audio Tape (DAT) est un support d enregistrement audio numérique sur bande magnétique 3.81mm conçu par Sony …   Wikipédia en Français

  • Digital Audio Tape — DAT Kassette mit Hülle im Größenvergleich mit einer Micro Batterie (4,4 cm lang) Das Digital Audio Tape (DAT) ist ein digitales Audio Magnetband (Tonband) für entsprechende Audiorekorder. Das Aufzeichnungsformat und die Tonqualität entsprechen im …   Deutsch Wikipedia

  • digital audio tape — N UNCOUNT Digital audio tape is a type of magnetic tape used to make very high quality recordings of sound by recording it in digital form. The abbreviation DAT is often used. Syn: DAT …   English dictionary

  • digital audio tape —    Abbreviated DAT. A method of recording information in digital form on a small audio tape cassette, originally developed by Sony and Hewlett Packard. The most common format is a 4millimeter, helical scan drive, which can hold more than 3GB of… …   Dictionary of networking

  • Digital Audio Tape — F/A/V Two channel digital audio has become increasingly common as a professional master reference and for use in field recording. (Sound) …   Audio and video glossary

  • Alesis Digital Audio Tape — Ein ADAT XT 8 Kanal Digital Audiorecorder Das Alesis Digital Audio Tape oder ADAT (eng. Alesis digitales Tonband) wurde 1993 von der gleichnamigen Firma eingeführt. Zum einen versteht man darunter das Aufnahmesystem, welches es ermöglicht,… …   Deutsch Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”