Porosity sealing

Porosity sealing

Porosity sealing, also known as vacuum impregnating, metal impregnating, polymer impregnating, and porous metal sealing, is the process of filling a porous substrate to make it airtight.

Process

Porosity sealing is a four step process:

  1. Air within the pores is expanded under reduced pressure (vacuum).
  2. Pressure reversal (adding pressure outside the part) saturates pores with monomer.
  3. Excess monomer is rinsed from the exterior surfaces of the part.
  4. The liquid monomer within the porosity is polymerized into a solid to seal the passage.

Common applications

Die castings and permanent mold castings commonly contain internal porosity. This porosity is generally localized to the deepest cross-sections of the part and does not extend to the outer skin. However, if the part is also machined, the internal porosity will be exposed and the part will leak if pressurized. Machined die castings that need to hold fluids (intake manifolds, coolant connectors, transmission cases, pump housings and fluid power components) are routinely sealed for life using acrylic resins. Because the sealant is internal to the part, the exterior dimensions and appearance of the part are unchanged.

Powder metallurgy

Powder metallurgy (PM) components are sealed prior to plating and to reduce internal corrosion. Plating operations typically involve submerging the parts in acid solutions. After plating, residual acid internal to the part can promote corrosion and/or preclude an acceptable plating finish. The solution to this problem is to seal the internal voids prior to plating. As explained above, the porosity is saturated with monomer and is then rinsed completely clear of the surface. The resin cures to a durable polymer. Thus, the exposed surface metal is free to be plated while the interior spaces are sealed dry.

The porosity in powder metal parts becomes a liability when the part must resist a differential pressure. PM applications for compressed air, fuel handling or hydraulic housings are common and effective; however, they must be sealed first. The polymer does not add structural strength to the physical part, but it will hold high pressures without creeping. If the wall thickness of the part exceeds 1/4 inch, the leak pressure is typically on the same order of magnitude as the burst pressure of the part.

Powder metal is also impregnated to enhance machinability. PM parts are generally difficult to machine and some compositions may not be machinable without ruining the cutting tool. Porosity sealing improves the life of cutting tools by ten to one-hundred times. Resin impregnation is more effective than compacting additives and can be selectively applied for near net pressed parts.[citation needed]


Wikimedia Foundation. 2010.

Игры ⚽ Поможем сделать НИР

Look at other dictionaries:

  • Electronic packaging — is a major discipline within the field of electronic engineering, and includes a wide variety of technologies. It refers to enclosures and protective features built into the product itself, and not to shipping containers. It applies both to end… …   Wikipedia

  • Casting defect — A casting defect is an irregularity in the metal casting process that is undesired. Some defects can be tolerated while others can be repaired otherwise they must be eliminated. They are broken down into five main categories: gas porosity,… …   Wikipedia

  • Casting (metalworking) — Casting iron in a sand mold In metalworking, casting involves pouring liquid metal into a mold, which contains a hollow cavity of the desired shape, and then allowing it to cool and solidify. The solidified part is also known as a casting, which… …   Wikipedia

  • Concrete sealers — are coatings applied to concrete to protect it from corrosion. They either block the pores in the concrete to reduce absorption of water and salts or form an impermeable layer which prevents such materials from passing.[1] Extensive research from …   Wikipedia

  • Electric Line — The term wireline usually refers to a cabling technology used by operators of oil and gas wells to lower equipment or measurement devices into the well for the purposes of well intervention and reservoir evaluation. Braided line can contain an… …   Wikipedia

  • pottery — /pot euh ree/, n., pl. potteries. 1. ceramic ware, esp. earthenware and stoneware. 2. the art or business of a potter; ceramics. 3. a place where earthen pots or vessels are made. [1475 85; POTTER1 + Y3] * * * I One of the oldest and most… …   Universalium

  • Gas tungsten arc welding — TIG welding of a bronze sculpture Gas tungsten arc welding (GTAW), also known as tungsten inert gas (TIG …   Wikipedia

  • Anodizing — Anodizing, or anodising, is an electrolytic passivation process used to increase the thickness of the natural oxide layer on the surface of metal parts. Anodizing increases corrosion resistance and wear resistance, and provides better adhesion… …   Wikipedia

  • papermaking — [pā′pər māk΄iŋ] n. the making of paper papermaker n. * * * pa·per·mak·ing (pāʹpər mā kĭng) n. The process or craft of making paper.   paʹper·mak er n. * * * Introduction       formation of a matted or felted sheet, usually of cellulose fibres,… …   Universalium

  • Water well — Village pump redirects here. For information on Wikipedia project related discussions see Wikipedia:Village pump. Water well at the Wald monastery in Germany. A water well is an excavation or structure created in the ground by digging, driving,… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”