Collet


Collet
Collets

A collet (play /ˈkɒlɨt/) is a holding device—specifically, a subtype of chuck—that forms a collar around the object to be held and exerts a strong clamping force on the object when it is tightened, usually via a tapered outer collar. It may be used to hold a workpiece or a tool.

A collet is a sleeve with a (normally) cylindrical inner surface and a conical outer surface. The collet can be squeezed against a matching taper such that its inner surface contracts to a slightly smaller diameter, squeezing the tool or workpiece whose secure holding is desired. Most often this is achieved with a spring collet, made of spring steel, with one or more kerf cuts along its length to allow it to expand and contract. An alternative collet design is one that has several tapered steel blocks (essentially tapered gauge blocks) held in circular position (like the points of a star, or indeed the jaws of a jawed chuck) by a flexible binding medium (typically synthetic or natural rubber). The Jacobs Rubber-Flex brand is a name that most machinists would recognize for this type of collet chuck system. Regardless of the collet design, the operating principle is the same: squeeze the collet against the tool or workpiece to be held, resulting in high static friction. Under correct conditions, it holds quite securely.

Contents

Nomenclature variations

Generally, a collet chuck, considered as a unit, consists of a tapered receiving sleeve (often integral with the machine spindle), the collet proper (usually made of spring steel), which is inserted into the receiving sleeve, and (often) a cap that screws over the collet, clamping it via another taper.

Usually in shop-floor terminology, the terms collet and chuck are used in contradistinction; users speak of holding a workpiece or tool with either a collet or a chuck. In this context "chuck" means any type of chuck other than a collet chuck (scroll chuck, independent-jaw chuck, etc.).

Advantages and disadvantages compared to other types of chuck

Each collet generally has only a narrow clamping range, which means that a large number of collets are required to hold a given range of materials in the chuck, unlike with many other types of chuck that will generally cover a wide range of sizes. This gives collet chucks the disadvantage of relatively high capital cost.

The collet's advantage over other chucks is that it manages to combine all of the following traits into one chuck, and this combination is highly valuable in an environment of repetitive part production:

  1. Speed of chucking (unclamp one part, switch to a new part, reclamp)
  2. Self-centering
  3. Strong clamping force
  4. Resistance against being jarred loose (untightened)
  5. Centering at a high level of precision (runout is less than 0.005 in (0.13 mm) TIR)

Of the above traits, scroll chucks offer always № 1 and № 2; usually № 3; to varying extents № 4 (depending on the situation); but not reliably № 5. Independent-jaw chucks offer always № 3; usually № 4; reliably № 5 (but at the expense of paying a skilled user to spend time achieving it); never № 2; and generally not № 1. Meanwhile, a collet chuck can deliver all 5 reliably, and with no need for a skilled user. (№s 3 to 5 do depend on the object being clamped closely matching the size and shape of the collet's clamping surface. This constraint is usually not a problem when the object is good-quality bar stock; the shank of a non-abused drill bit, reamer, endmill, etc.; or a previously machined part that is being rechucked for additional cutting operations.)

Examples of collet applications in various industries

Woodwork

On a wood router (a hand-held or table-mounted power tool used in woodworking), the collet is what holds the bit in place. In the U.S. it is generally for 0.25 or 0.5 inch (6.3 or 13 mm) bits, while in Europe bits are most commonly 6 or 8 mm (0.24 or 0.31 in). The collet is hexagonal on the outside so it can be tightened or loosened with a standard wrench, and has threads on the inside so it can be screwed on to the motor arbor.

Metalworking

A selection of machine collets

There are hundreds of designs of collet used in the metalworking industry. Common industry-standard designs for manual mills are 5C[1] and R8[2], however most are proprietary designs that only fit one specific manufacturer's equipment. Collets can range in holding capacity from zero to several inches in diameter. The most common type of collet is one that grips a round bar or tool, but there are collets for square, hexagonal, and other shapes. In addition to the outside-holding collets that are so common, there are collets that are used for holding a part on its inside surface so that it can be machined on its outside surface (basically, akin to an expanding mandrel). Furthermore, it is not uncommon for users to make a custom (bespoke) collet to hold any unusual size or shape of part. These are often called emergency collets (e-collets) or soft collets (from the fact that they are bought in a soft (non-hardened) machinable state and cut as needed to fit). Yet another type of collet is a step collet, which steps up to a larger diameter from the spindle (analogous to how a mushroom cap is larger than the stem). Step collets allow the holding of rather large workpieces, as long as they need not pass into the spindle through-hole—for example, disc-shaped workpieces.

In the accompanying photo, the two top left collets are the side and end view of one style of collet; the two right collets are from a smaller range. The lower image is of a disassembled pin chuck that is used to hold small drills or workpieces. The leftmost part is the body, the collet is shown protruding from the body, and the nose cap is separate, on the right.

In use, the part to be held is inserted into the collet, and then the collet is pushed (via a nose cap) or pulled (via a drawbar) fully into the body (which has a taper to match the collet machined into the front). When the nose cap or drawbar is tightened properly, enough force is applied to the collet that the tapers at the front and back of the collet are pushed into their matching tapers, causing the collet to constrict in diameter. This constriction exerts considerable force onto the shank of the workpiece or tool that is being held in the collet. It is then securely held against any forces it may encounter during normal operation.

Craft hobbies

Many users (hobbyists, graphic artists, architects, students, and others) may be familiar with collets as the part of an X-Acto or equivalent knife that holds the blade. Another common example is the collet that holds the bits of a Dremel or equivalent rotary file.

Semiconductor work

In semiconductor industry, a die collet is used for picking a die up from a wafer after die cutting process has finished, and bonding it into a package. Some of them are made with rubber, and use vacuum for picking.

Internal combustion engines

The two halves of the collar which fits around the stem of a valve and traps the spring against the cylinder head are known as split collets.

References

Bibliography

External links


Wikimedia Foundation. 2010.

Look at other dictionaries:

  • collet — [ kɔlɛ ] n. m. • fin XIe « cou »; dimin. de col 1 ♦ (XIIIe) Vx ou loc. Partie du vêtement qui entoure le cou. ⇒ col, collerette. Un collet de dentelle. ♢ Loc. adj. COLLET MONTÉ : qui affecte l austérité, la …   Encyclopédie Universelle

  • collet — COLLET. substant. maseul. Cette partie de l habillement qui est autour du cou. Collet de pourpoint. Collet de manteau.Collet, étant mis absolument, se prend pour Cette pièce de toile qu on met autour du cou par ornement, et qui s appelle… …   Dictionnaire de l'Académie Française 1798

  • collet — Collet. s. m. Cette partie de l habit, qui est alentour du cou. Collet de pourpoint. collet de manteau. collet de robe. collet de chemise &c. Collet, estant mis absolument, Se prend pour cette piece de toile que l on met autour du cou par… …   Dictionnaire de l'Académie française

  • Collet — ist der Familienname folgender Personen: André Collet (* 1971), deutscher Ausdauerläufer Cédric Collet (* 1984), französischer Fußballspieler Clara Elizabeth Collet (1860–1948), britische Soziologin Giancarlo Collet (* 1945), katholischer… …   Deutsch Wikipedia

  • Collet — Col let, n. [F. collet, dim. fr. L. collum neck. See {Collar}.] 1. A small collar or neckband. Foxe. [1913 Webster] 2. (Mech.) A small metal ring; a small collar fastened on an arbor; as, the collet on the balance arbor of a watch; a small socket …   The Collaborative International Dictionary of English

  • collet — Collet, la partie pres du col. Prens le par le collet, et le meine en justice, Collum abstringe. Un collet, ou gorgias dequoy les femmes couvrent leurs poitrines, Strophium, Focale, Fascia, vel quid simile, quo collum obuoluitur. B. ex… …   Thresor de la langue françoyse

  • collet — 1520s, from Fr. collet little collar, dim. of col neck, from L. collum (see COLLAR (Cf. collar)) …   Etymology dictionary

  • collet — [käl′it] n. [Fr, dim. of col, the neck < L collum: see COLLAR] 1. a metal band or ring, such as is used in a watch to hold the end of a balance spring 2. a small metal band used in ring settings 3. a chuck with a conical or tapered end, for… …   English World dictionary

  • Collet — Collet. См. Цанговый патрон. (Источник: «Металлы и сплавы. Справочник.» Под редакцией Ю.П. Солнцева; НПО Профессионал , НПО Мир и семья ; Санкт Петербург, 2003 г.) …   Словарь металлургических терминов

  • Collet — (fr.), 1) Kragen, Krägelchen, Halskragen; 2) Reitjacke, Weste mit Ärmeln u. ohne Schößen, welche genau an den Körper anschließt u. von Kindern, Reitern u. solchen. Personen getragen wird, welchen bei ihrer Arbeit ein langer Rock hinderlich sein… …   Pierer's Universal-Lexikon

  • Collet — (franz., spr. lä), s. Kollett …   Meyers Großes Konversations-Lexikon


Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”

We are using cookies for the best presentation of our site. Continuing to use this site, you agree with this.