Traffic measurement (telecommunications)

Traffic measurement (telecommunications)

Measurement of traffic within a network allows network managers and analysts to both make day-to-day decisions about operations and to plan for long-term developments [1, 2] . Traffic Measurements are used in many fundamental activities such as [2] :

*Identification of traffic patterns and trends
*Calculating the traffic intensity in a specific circuit or group
*Monitoring the service
*Dimensioning and managing the network
*Calculating tariffs
*Performing forecasting
*Dimensioning and managing the SS7network
*Checking the performance of the common channel signalling network

The following sections will answer some fundamental questions about Traffic Measurement, such as: What should be measured; when should it be measured; what assumptions are made; and what errors can occur?

When should traffic be measured?

Traffic Measurements are conducted on a continuous basis and the results compiled into reports for management which are used in management decisions on various time scales. Measurements that are taken every few minutes are used for network management and temporary routing, measurements every few hours, days and weeks are used for maintenance purposes and measurements that are taken over months or even years are used for long-term network deployment, upgrading and extensions [2] .

To determine normal reference traffic for a network, the ITU recommends that a network traffic analyst must take measurements for the busiest hour of each day for a whole year [2] . The busiest hour is defined as that four consecutive quarter hours whose traffic intensity is the greatest. Measurements taken outside the busy hour can be discarded. The reference intensity of traffic is then calculated by taking the average traffic intensity of the top thirty days in the year [2] . Measurements taken on individual days can be discarded. This will give the normal high traffic intensity in the network, allowing network managers to make long-term strategic decisions [2] .

Assumptions made when calculating circuits required

To perform calculations in circuit-switched networks several assumptions are made [3] :

*Calls arrivals follow a Poisson distribution
*Holding times follow a Negative Exponential distribution
*Blocked calls are lost or overflow
*There is statistical equilibrium

It is useful to remember that the measurements are averages, and this process deliberately ignores very short term variations in the traffic, but still allows for a small but finite loss. The above assumptions are accurate if applied to circuit switched networks; however they fail when planning for data traffic, small exchanges and sudden sharp peaks in traffic such as that caused by TV and radio phone-in competitions.

Traffic measurement errors

Measurement errors are caused by faults in equipment or constraints on equipment design. The following five errors are examples of some types of errors that can occur [2] :

*"Post-processing errors" – These errors are generated by operators when analysing data that has been measured
*"Pre-processing errors" – These errors are generated by computers when compiling data for operators
*"Statistical errors" – These errors are caused by the averages in traffic measurements and by the fact that measurements are made from discrete samples
*"Database errors" – These errors exist when errors are generated by faults in the storage of information
*"Interpretation errors" – These errors occur when analysts misinterpret data

References

[1] Penttinen A., "Chapter 4 – Traffic Modelling and Measurements", Lecture Notes: S-38.145 - Introduction to Teletraffic Theory, Helsinki University of Technology, Fall 1999.

[2] Kennedy I., "Why Traffic Measurement?", School of Electrical and Information Engineering, University of the Witwatersrand, 2003.

[3] Kennedy I., "What basic data should we measure?", School of Electrical and Information Engineering, University of the Witwatersrand, 2003.


Wikimedia Foundation. 2010.

Игры ⚽ Нужно решить контрольную?

Look at other dictionaries:

  • Telecommunications in the People's Republic of China — Telecommunications in China redirects here. For the industry, see Telecommunications industry in China. This article is about Communications in the People s Republic of China, excluding Hong Kong and Macau (see Communications in Hong Kong and… …   Wikipedia

  • telecommunications media — Introduction       equipment and systems metal wire, terrestrial and satellite radio, and optical fibre employed in the transmission of electromagnetic signals. Transmission media and the problem of signal degradation       Every… …   Universalium

  • Telecommunications forecasting — All telecommunications service providers perform forecasting calculations to assist them in planning their networks.Farr R.E., Telecommunications Traffic, Tariffs and Costs – An Introduction For Managers, Peter Peregrinus, 1988.] Accurate… …   Wikipedia

  • Traffic flow (computer networking) — For other uses, see Flow (disambiguation). In packet switching networks, traffic flow, packet flow or network flow is a sequence of packets from a source computer to a destination, which may be another host, a multicast group, or a broadcast… …   Wikipedia

  • Call (telecommunications) — In computer science and telecommunications a call is: * Any attempt to set up a telecommunication circuit * A unit of traffic measurement * The actions performed by a call originator * The action of bringing a computer program, subroutine, or… …   Wikipedia

  • List of unusual units of measurement — For units of measure primarily used in countries where English is not the main language, see the article specific to that country, a list of which can be found in the systems of measurement article. An unusual unit of measurement is a unit of… …   Wikipedia

  • Network traffic simulation — is a process used in telecommunications engineering to measure the efficiency of a communications network. Contents 1 Overview 2 Simulation methods 3 Advantages of simulation 4 …   Wikipedia

  • Provider Backbone Bridge Traffic Engineering — Dans le domaine des télécommunications, Provider Backbone Bridge Traffic Engineering (PBB TE), également connu sous le nom de Provider Backbone Transport (PBT), est un protocole de communication Ethernet de classe opérateur. Il repose sur des… …   Wikipédia en Français

  • erlang — (E)    a measure of telecommunications traffic density. The erlang is a dimensionless unit representing a traffic density of one call second per second (or one call hour per hour, etc.). The erlang is sometimes divided into 36 unit calls or 30… …   Dictionary of units of measurement

  • unit call — (UC)    a measure of telecommunications traffic density. The unit call is a dimensionless unit representing a traffic density of 100 call seconds per hour, or 1/36 erlang …   Dictionary of units of measurement

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”