Flow control

Flow control

distinguish|control flowIn computer networking, flow control is the process of managing the rate of data transmission between two nodes to prevent a fast sender from over running a slow receiver. This should be distinguished from congestion control, which is used for controlling the flow of data when congestion has actually occurred ref|ATM-Traffic-Management. Flow control mechanisms can be classified by whether or not the receiving node sends feedback to the sending node.

Flow control is important because it is possible for a sending computer to transmit information at a faster rate than the destination computer can receive and process them. This can happen if the receiving computers have a heavy traffic load in comparison to the sending computer, or if the receiving computer has less processing power than the sending computer.

Transmit flow control

Transmit flow control may occur between data on and off terminal equipment (DTE) and a switching center, via data circuit-terminating equipment (DCE), or between two DTEs. The transmission rate may be controlled because of network or DTE requirements. Transmit flow control can occur independently in the two directions of data transfer, thus permitting the transfer rates in one direction to be different from the transfer rates in the other direction. Transmit flow control can be either stop-and-go or use a sliding window.

Flow control can be done either by control lines in a data communication interface (see serial port and RS 232), or by reserving in-band control characters to signal flow start and stop (such as the ASCII codes for XON/XOFF). Common RS 232 control lines are RTS (Request To Send)/CTS (Clear To Send) and DSR (Data Set Ready)/DTR (Data Terminal Ready), which is usually referred to as "hardware flow control". XON/XOFF is usually referred to as "software flow control". In the old mainframe days, modems were called "data sets", hence the survival of the term.

Hardware flow control typically works by the DTE or master end first raising or asserting its line, such as RTS, which signals the opposite end (the slave end such as a DCE) to begin monitoring its data input line. When ready for data, the slave end will raise its complementary line, CTS in this example, which signals the master to start sending data, and for the master to begin monitoring the slave's data output line. If either end needs to stop the data, it lowers its respective line. For PC-to-modem and similar links, DTR/DSR are raised for the entire modem session (say a dialup internet call), and RTS/CTS are raised for each block of data.

An earlier version of this section was based on Federal Standard 1037C.

Open-loop flow control

The open-loop flow control mechanism is characterized by having no feedback between the receiver and the transmitter. This simple means of control is widely used. The allocation of resources must be a “prior reservation” or “hop-to-hop” type. The Open Loop flow control has inherent problems with maximizing the utilization of the ATM network resources. Resource allocation is made at connection setup using a CAC (Connection Admission Control) and this allocation is made using information that is already “old news” during the lifetime of the connection. Often there is an over-allocation of resources. Open-Loop flow control is used by the CBR, VBR and UBR services (see traffic contract and congestion control) ref|ATM-Traffic-Management.

Closed-loop flow control

The Closed Loop flow control mechanism is characterized by the ability of the network to report pending network congestion back to the transmitter. This information is then used by the transmitter in various ways to adapt its activity to existing network conditions. Closed Loop flow control is used by ABR (see traffic contract and congestion control) ref|ATM-Traffic-Management. Transmit Flow Control described above is a form of Closed-loop flow control.

See also

* Software flow control
* Computer networking
* Traffic contract
* Congestion control
* Teletraffic engineering in broadband networks
* Teletraffic engineering
* Ethernet flow control
* Handshaking

References

# [http://scholar.google.com/scholar?hl=en&lr=&safe=off&q=cache:FAB0FGEX85cJ:www.parallaxresearch.com/dataclips/pub/infotech/protocols/ATM/ATM_Traffic_Mgmt.PDF+comparison+GCRA+algorithms Network Testing Solutions, ATM Traffic Management White paper] last accessed 15 March 2005.

External links

* [http://www.lammertbies.nl/comm/info/RS-232_flow_control.html RS232 flow control and handshaking]


Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • Flow Control —   [engl.], Flusssteuerung …   Universal-Lexikon

  • flow control —    1. In communications, control of the rate at which information is exchanged between two computers over a transmission channel. Flow control is needed when one of the devices cannot receive the information at the same rate as it can be sent,… …   Dictionary of networking

  • Flow Control — Mit Datenflusskontrolle (engl. data flow control) oder Datenflusssteuerung werden unterschiedliche Verfahren bezeichnet, mit denen die Datenübertragung von Endgeräten an einem Datennetz, die nicht synchron arbeiten, so gesteuert wird, dass eine… …   Deutsch Wikipedia

  • Flow Control — Для улучшения этой статьи желательно?: Добавить иллюстрации. Flow Control (Управление потоком передачи данных)  в компь …   Википедия

  • flow control — srauto valdymas statusas T sritis automatika atitikmenys: angl. flow control; traffic control vok. Ablaufregelung, f; Flußregelung, f; Flußsteuerung, f; Verkehrssteuerung, f rus. управление потоком, n pranc. commande de flux, f; régulation de… …   Automatikos terminų žodynas

  • flow control — control of data transfer between two computers …   English contemporary dictionary

  • Flow control valve — Globe control valve with the pneumatic actuator and smart positioner A flow control valve regulates the flow or pressure of a fluid. Control valves normally respond to signals generated by independent devices such as flow meters or temperature… …   Wikipedia

  • Flow control structure — A flow control structure is some type of construction that alters the flow of water in some way. As a group these are passive structures since they operate without intervention under different amounts of water flow and their impact changes based… …   Wikipedia

  • flow-control valve — A fluid powered valve that controls the volume or the direction of fluid flow. Flow control valves, like check valve and selector valves, are normally used along with pressure control valves in fluid power systems. See flapper valve …   Aviation dictionary

  • flow control — Measures designed to adjust the flow of traffic into a given airspace, along a given route, or bound for a given aerodrome, so as to ensure the most effective utilization of the airspace (ICAO). ATC (air traffic control) may apply restrictions to …   Aviation dictionary

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”