Expeller pressing

Expeller pressing

Expeller pressing (also called oil pressing) is a mechanical method for extracting oil from raw materials. The raw materials are squeezed under high pressure in a single step. When used for the extraction of food oils, typical raw materials are nuts, seeds and algae, which are supplied to the press in a continuous feed. Expeller presses can recover 75% of the oil from algae.[citation needed] As the raw material is pressed, friction causes it to heat up; in the case of harder nuts (which require higher pressures) the material can exceed temperatures of 120 °F.[1]

Example of an expeller
Coconut Oil is expelled from Copra at an oil mill in Tripunithura, Kerala, India

An expeller press is a screw-type machine that presses oil seeds through a caged barrel-like cavity. Raw materials enter one side of the press and waste products exit the other side. The machine uses friction and continuous pressure from the screw drives to move and compress the seed material. The oil seeps through small openings that do not allow seed fiber solids to pass through. Afterward, the pressed seeds are formed into a hardened cake, which is removed from the machine. Pressure involved in expeller pressing creates heat in the range of 140-210 F (60-99 C). Some companies claim that they use a cooling apparatus to reduce this temperature to protect certain properties of the oils being extracted.

Expeller processing cannot remove every last trace of liquid (usually oil) from the raw material. A significant amount remains trapped inside of the cake leftover after pressing. In most small scale rural situations this is of little or no importance as the cake that remains after the oil has been removed finds uses in local dishes, in the manufacture of secondary products or for animal feed. Some raw materials however do not release oil by simple expelling; the most notable being rice bran. In order to remove oil from commodities that do not respond to expelling or to extract the final traces of oil after expelling it is necessary to use solvent extraction.

The earliest expeller presses utilized a continuous screw design. The compression screws were much like the screw of a screw conveyor. That is, the helicoid flighting started at one end and ended at the other. Valerius Anderson invented the interrupted screw design and patented it in the year 1900.

What Anderson observed was that, in the continuous flighting arrangement of a compression screw, there are tendencies for slippery materials either to co-rotate with the screw or to pass through with minimal dewatering. He wrote that "brewers' slops, slaughter-house refuse" and other "soft and mushy" materials dewater poorly in continuous screw presses.

His invention consisted of putting interruptions in the flighting of a compression screw. It was much like having a hanger bearing in a screw conveyor: there is no flighting on the shaft at that point, so material tends to stop moving and pile up. It is only after solids accumulate in the gap that the downstream flighting catches material. When this happens, material is forced along its way. The result was better dewatering, a more consistent press cake.

As the years went by, applications of the interrupted screw design were expanded beyond slippery and slimy materials. This took place because competing continuous screw presses worked best only under conditions of constant feed, at constant consistency. If either the consistency or the flow rate diminished, squeezing would diminish until it was inadequate for proper moisture removal. At the same time, if the consistency increased, the press could jam. To counteract these tendencies it was necessary to build a very heavy press, frequently with an expensive variable speed drive.

In contrast, it was found that the interruptions in the flighting of the Anderson screw would provide cushion within the press. If consistency went down, compression was still effective. A plug of sufficiently solid material had to build up at each interruption before solids could progress towards the discharge. This self-correcting performance prevents wet material from purging at the cake discharge. It is achieved without varying the speed of the screw.

The economic advantages of these characteristics led to interrupted screw presses being used to dewater fibrous materials that are neither slippery nor slimy. Examples would be alfalfa, cornhusk, and, more recently, paper mill fibers.

After the 1900 patent, a major improvement was made with the addition of resistor teeth. Fitted into the gaps where there is no flighting, these teeth increase the agitation within the press, further diminishing co-rotation tendencies.

See also

External links

References

  1. ^ [1]

Wikimedia Foundation. 2010.

Игры ⚽ Поможем решить контрольную работу

Look at other dictionaries:

  • expeller — ikˈspelə(r), ek noun ( s) : one that expels: as a. : a screw press for expressing vegetable oil from soybeans or other seeds b. : an operator of a machine for pressing liquid and tallow from tankage …   Useful english dictionary

  • Mill (grinding) — Mill A tabletop hammer mill Other names Grinding mill Uses Grinding Related items Mortar and pestle Expeller Extruder A grinding mill is …   Wikipedia

  • Neem oil — Neem Expeller Oil Neem oil is a vegetable oil pressed from the fruits and seeds of the neem (Azadirachta indica), an evergreen tree which is endemic to the Indian subcontinent and has been introduced to many other areas in the tropics. It is,… …   Wikipedia

  • Vegetable fats and oils — Vegetable oil redirects here. For other uses, see Vegetable oil (disambiguation). Plant oils Olive oil Types Vegetable fats (list) …   Wikipedia

  • Algaculture — is a form of aquaculture involving the farming of species of algae. The majority of algae that are intentionally cultivated fall into the category of microalgae (also referred to as phytoplankton, microphytes, or planktonic algae). Macroalgae,… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”