Injection well

Injection well

An injection well is an underground well into which water, other liquids, or gases are injected instead of being pumped out.

Applications

Injection wells are used for many purposes. One of these is waste water dumping, in which waste water is injected into the ground between impermeable layers of rocks to avoid polluting fresh water supplies. In this case, when the injection well is full, it would be cemented to seal it to avoid leakage from the injection point.

Another use of injection wells is in petroleum production. Steam, carbon dioxide, water, and other substances can be injected into an oil-producing unit in order to heat the oil and/or lower its viscosity, allowing it to flow to a producing well nearby.

Yet another use for injection wells is in environmental remediation, for cleanup of either soil or groundwater contamination. Injection wells can insert clean water into an aquifer, thereby changing the direction and speed of groundwater flow, perhaps towards extraction wells downgradient, which could then more speedily and efficiently remove the contaminated groundwater. Injection wells can also be used in cleanup of soil contamination, for example by use of an ozonation system. Complex hydrocarbons and other contaminants trapped in soil and otherwise inaccessible can be broken down by ozone, a highly reactive gas, often with greater cost-effectiveness than could be had by digging out the affected area. Such systems are particularly useful in built-up urban environments where digging may be impractical due to overlying buildings. [ [http://yosemite.epa.gov/opa/admpress.nsf/6427a6b7538955c585257359003f0230/7bfcdcd6fef70da285257163005c159c!OpenDocument East Islip Superfund Site cleanup] ; example of use of ozonation wells for remediation in situ]

Theoretically, a injection well is a safe way to dump waste waters as wastes are injected into layer of rocks where water can't go through and building an injection well is strictly controlled, however injection wells are known to be prone to leaking because of earthquakes and fractures in the rock structure.

Regulatory requirements

In the United States, injection well activity is regulated by the United States Environmental Protection Agency (EPA) and state governments under the Safe Drinking Water Act. EPA has issued Underground Injection Control (UIC) regulations in order to protect drinking water sources.

Notes

References

* [http://www.frtr.gov/matrix2/section4/4-54.html Deep Well Injection]
* [http://www.pollutionissues.com/Ho-Li/Injection-Well.html Injection Well]

External links

* [http://www.epa.gov/safewater/uic EPA - Underground Injection Control Program]


Wikimedia Foundation. 2010.

Игры ⚽ Нужно сделать НИР?

Look at other dictionaries:

  • injection well —    Well used for emplacing fluids into the subsurface [22] …   Lexicon of Cave and Karst Terminology

  • injection well — noun : a well into which gas, air, or water is pumped in order to increase the yield of adjacent wells …   Useful english dictionary

  • Injection molding of liquid silicone rubber — (LSR) is a process to produce pliable, durable parts in high volume.Liquid silicone rubber is a high purity platinum cured silicone with low compression set, great stability and ability to resist extreme temperatures of heat and cold ideally… …   Wikipedia

  • Injection molding — (British: moulding) is a manufacturing process for producing parts from both thermoplastic and thermosetting plastic materials. Molten plastic is injected at high pressure into a mold, which is the inverse of the product s shape. After a product… …   Wikipedia

  • Injection pump — for a 12 cylinder diesel engine An Injection Pump is the device that pumps fuel into the cylinders of a diesel engine or less typically, a gasoline engine. Traditionally, the pump is driven indirectly from the crankshaft by gears, chains or a… …   Wikipedia

  • injection string — noun (mining) A pipe run in addition to the production string in the borehole to allow the passage of additives or of drilling mud to stop the well (also called kill string) • • • Main Entry: ↑inject …   Useful english dictionary

  • Injection (medicine) — This article is about the medical procedure. For other uses, see Injection. A Somali boy receiving a subcutaneous injection of polio vaccine An injection (often referred to as a shot or a jab ) is an infusion method of putting fluid into the body …   Wikipedia

  • Well kill — A well kill refers to the operation of placing a column of heavy fluid into a well bore in order to prevent the flow of reservoir fluids without the need for pressure control equipment at the surface. It works on the principle that the weight of… …   Wikipedia

  • Well intervention — A well intervention, or well work , is any operation carried out on a oil or gas well during , or at the end of its productive life, that alters the state of the well and or well geometry, provides well diagnostics or manages the production of… …   Wikipedia

  • injection zone —    A geological ‘formation,’ group of formations, or part of a formation receiving fluids through a well …   Lexicon of Cave and Karst Terminology

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”